Table des Matières
Publicité
www.freeservicemanuals.info
1.1 DISASSEMBLY FLOW CHART
This flowchart lists the disassembling steps for the cabinet
parts and P.C. boards in order to gain access to item(s) to
be serviced. When reassembling, perform the step(s) in re-
verse order. Bend, route and dress the flat cables as they
were originally laid.
1
2
3
4
5
6
7
8
1.2 HOW TO READ THE DISASSEMBLY AND ASSEMBLY
<Example>
Step/
Part Name
Loc No.
1
Top cover,
Bracket
(1)
(1) Order of steps in Procedure
When reassembling, perform the step(s) in the reverse order.
These numbers are also used as the identification (location) No.
of parts Figures.
(2) Part name to be removed or installed.
(3) Fig. No. showing procedure or part location.
(4) Identification of part to be removed, unhooked, unlocked,
released, unplugged, unclamped or unsoldered.
P= Spring, W= Washer, S= Screw, L= Locking tab, SD= Solder,
CN**(WR**)= Remove the wire (WR**) from the connector
(CN**).
Note:
• The bracketed ( ) WR of the connector symbol are as-
signed nos. in priority order and do not correspond to
those on the spare parts list.
(5) Adjustment information for installation
Top cover, Bracket
Bottom cover
Front panel assembly
Drum assembly
Mechanism assembly
SW/Display board assembly
P/S Converter board assembly
Main board assembly
Fig.
Point
No.
D1 4(S1a),(S1b),3(L1a),
2(SD1a),(P1a),
CN1(WR1a),
2(S1c)
(2)
(3)
(4)
SECTION 1
DISASSEMBLY
1.3 DISASSEMBLY/ASSEMBLY METHOD
Step/
Loc No.
1
2
3
4
5
6
7
8
<Note 2>
• When attaching the Bottom cover, make sure that the Earth
plate of the Bottom cover is passed through the hole of the
Note
Bottom chassis and then touches the GND (Ground) on the
Main board assembly.
<Note 1>
<Note 3a>
• Be careful not to damage the connector and wire etc. during
connection and disconnection.
When connecting the wire to the connector, be careful with the
wire direction.
(5)
<Note 3b>
• When reattaching the Front panel assembly, make sure that
the door opener
in position prior to the reinstallation.
<Note 5a>
• When it is required to remove the screws (S5a) retaining the
Mechanism assembly, please refer to the "Procedures for Low-
ering the Cassette holder assembly"(See on pages 1-2).
• When removing the Mechanism assembly only, unhook the two
spacers connecting it with the Main board assembly with pliers
from the back side of the Main board assembly first, and then
remove the Mechanism assembly.
• When reattaching the Mechanism assembly to the Main board
assembly, take care not to damage the sensors on the Main
board assembly (D3001: LED, Q3002: Start sensor, Q3003:
End sensor, S3002 : S cassette switch).
<Note 5b>
• The wire (WR5) has excess length that may be loose, as it is
quite long. After inserting the wire and connectors, the loose
portion of the wire should be taken up and accommodated be-
tween the A/C head base and the main deck.
<Note 6>
• The REC safety board assembly is attached to the SW/Display
board assembly. It is therefore necessary to remove the REC
safety board assembly before removing the SW/Display board
assembly.
Published in Heiloo Holland
Fig.
Part Name
No.
Top cover,
D1 4(S1a), (S1b)
- - - - - - - - - - - - - - - - - -
Bracket
2(S1c)
Bottom cover
D2 4(L2a),3(L2b),(S2a), <Note 2>
2(S2b)
- - - - - - - - - - - - - - - - - -
Earth plate
Front panel assembly D3 7(L3),CN901(WR3a), <Note 3a>
CN7002(WR3b)
[HR-S6700MS]
CN3012(WR3b)
[HR-S7700MS]
- - - - - - - - - - - - - - - - - -
2(S3),Jack board assy
Drum assembly
D4 3(S4),CON1(WR4a), <Note 3a>
CN1(WR4b)
- - - - - - - - - - - - - - - - - -
(Inertia plate)
4(L4a)
- - - - - - - - - - - - - - - - - -
(Roller arm assy)
(P4), (L4b)
Mechanism assembly D5 2(S5a),(S5b),(S5c), <Note 3a>
2(L5), CN1(WR5)
SW/Display board
D6 CN7001(WR6a),
assembly
CN7191(WR6b),
(L6a),
REC safety board assy,
2(L6b), 5(L6c)
P/S Converter board
D7 2(S7),
assembly
CN3501(WR7a),
CN3502(WR7b)
Main board assembly D8 2(S8), (L8)
a
of the Cassette holder assembly is lowered
8/6/2016
Point
Note
<Note 3b>
<Note 5a>
<Note 5b>
<Note 3a>
<Note 6>
<Note 3a>
1-1
Publicité
Chapitres
Table des Matières
