Table des Matières
Publicité
www.freeservicemanuals.info
[Perform adjustments steps (7) to (10) only for 2 Head
models equipped with LP mode.]
(7) Then play back the alignment tape (A2).
(8) Press the channel buttons (+, –) simultaneously to enter
the manual tracking mode. This also brings tracking to
the center (centre).
(9) Perform the tracking operation and make sure that the
V.PB FM waveform is at its maximum.
(10) If it is not at maximum, loosen the screws (4) and (5),
and turn the A/C head positioning tool to bring the A/C
head to a position, around where the waveform reaches
its maximum for the first time. Then tighten the screws
(4) and (5).
Note:
• After adjusting, always perform the confirmation and
re-adjustment of the item 2.3.4.
Toward the drum
A/C head positioning tool
Audio control head
Drum side
2.3.4 Checking/Adjustment of the Standard Tracking
Preset
Signal
Mode
Equipment
Measuring point (D)
External trigger
Adjustment part
Specified value
Adjustment tool
Toward the capstan
Head base
Screw (4)
To the drum
Screw (5)
To the capstan
Fig. 2-3-3a
Alignment tape
Alignment tape
[SP, stairstep]
[EP(LP), stairstep]
played with the
played with the
SP head
EP(LP) head
X-value adjustment point
Control head position
Capstan side
Maximum
Fig. 2-3-3b
•
(A)
Alignment tape(LP, stairstep, PAL) [MHPE-L]
•
PB ¥ Auto adjust
(B)
•
(C)
Oscilloscope
•
TP106 (PB. FM)
•
(E)
TP111 (D.FF)
•
(F)
Jig RCU: Code "50"
•
(G)
STOP mode
(Maximum V.PB FM waveform)
•
(H)
Jig RCU [PTU94023B]
Published in Heiloo Holland
(1) Play back the alignment tape (A).
(2) Apply the external trigger signal to D.FF (E), to observe
the V.PB FM waveform at the measuring point (D).
(3) Confirm that the automatic tracking operation is com-
pleted.
(4) Set the VCR to the Auto adjust mode by transmitting the
code (F) twice from the Jig RCU. When the VCR enters
the stop mode, the adjustment is completed.
(5) If the VCR enters the eject mode, perform adjustment for
the audio control head phase (X-value) again.
2.3.5 Checking/Adjustment of the Tension Pole Position
•
Signal
(A)
Back tension cassette gauge
[PUJ48076-2]
•
Mode
(B)
PB
•
Adjustment part
(F)
Adjust pin [Mechansim assembly]
25 - 51 gf•cm (2.45 – 5 × 10
•
Specified value
(G)
(1) Play back the back tension cassette gauge (A).
(2) Check that the indicated value on the left side gauge is
within the specified value (G).
(3) If the indicated value is not within the specified value (G),
perform the adjustment in a following procedure.
1) Set the VCR to the mechanism service mode. (See
1.5 MECHANISM SERVICE MODE.)
2) Set the VCR to the play back mode and adjust by turn-
ing adjustment pin to align the tension arm assembly
edge with the main deck hole (A) on the right edge
marker. (See Fig. 2-3-5a)
Tension arm
assembly
Edge
Hole (A)
Marker
0.5 mm
Tension arm assembly
Tension brake assembly
Fig. 2-3-5a
8/6/2016
-3
Nm]
Adjust pin
2-18
Publicité
Chapitres
Table des Matières
