Warranty; Spare Parts; Troubleshooting; Agrilaser ® Autonomic - Agrilaser Autonomic Mode D'emploi

6. Warranty

CAUTION: Disassembly attempts of the product void warranty.
The Agrilaser Autonomic is developed and produced according to the
highest quality standards. Should you encounter any problems with your
product, please carefully read this manual. If your Agrilaser Autonomic
shows a defect or if you need assistance, please contact your local Agrilaser
dealer. Should any defect arise as a result of production faults, free repair or
replacement is guaranteed. The Agrilaser Autonomic has a warranty period
of 12 months, starting on the date of purchase. In case of replacement, the
warranty period of the original product will remain valid.
Warranty conditions
The warranty is valid if the Agrilaser Autonomic is used according to the
instructions of the manual and for the purpose for which it was designed.
The warranty is valid when a valid receipt is presented which shows the date
of purchase, the name of the dealer and the product name.
The warranty is invalid when:
• Damage due to falling or jolting occurs.
• The serial number has been removed.
• Parts of the product are disassembled.
• Any (attempts of) repairs have been carried out by unauthorized persons.
• Any defects have occurred as a result of using other equipment than provided
by Bird Control Group (for example, but not only, using a different adapter).
• Any defects occurred as a result of misuse or use in environments that are
not prescribed.
• Any defects as a result of environmental influences.
• The defect is due to normal wear of replaceable parts, such as, but not
only, the battery.

7. Spare parts

The following spare parts are available for the Agrilaser Autonomic. For
requests of spare parts contact your local Agrilaser dealer.
Spare parts
Laser module
Motor platform
Emergency stop
Power adapter (EU, UK or US)
Power adapter (industrial universal socket)
Supporting frame
USB-cable
Agrilaser Software (on USB drive)
Solar panel
Battery box
Battery
Installation guide

8. Troubleshooting

If the Agrilaser Autonomic is not performing as expected, check the LED
indicator on the back of the laser module to identify the system status.
LED indicator appearance System status
Red continuously Error
Red blinking Low battery
Orange continuously Teaching mode
Orange blinking Standby, calibrating
Green continuously Operational, preparing for burst, bursting
Green blinking Operational, waiting for next burst
None No power
Red continuously: An error occurred. Turn off the Agrilaser Autonomic by
pressing the ON/OFF button. Make sure all cables are connected properly
and the power adapter is in place. In addition, make sure no objects are
stuck between the moving parts. After at least one minute, turn on the
Agrilaser Autonomic by pressing the ON/OFF button. Make sure the
emergency switch is released.
Red blinking: The battery power is low (in case of a battery powered
system). Consider replacement of the battery or switch to city power supply
to continue operation.
Orange continuously: The Agrilaser Autonomic is in teaching mode (the user
creates a new pattern or edits an existing pattern).
Orange blinking: The Agrilaser Autonomic is in standby mode. No patterns
will be executed. Connect the Agrilaser Autonomic to your computer,
execute the software and press 'Start' in the overview screen to activate the
Agrilaser Autonomic.
Green continuously: The Agrilaser Autonomic is preparing the system for
bursting (laser is still off) or is performing a burst (laser is on).
Green blinking: At this point the Agrilaser Autonomic is waiting to perform
its next burst. This can either be during the interval in between bursts or
because the current time is outside the activated timeslot(s). The laser will
start bursting again only if at least one pattern has been created and has
been assigned an active timeslot.
None: The Agrilaser Autonomic is either switched off, not connected to a
power source or the emergency switch has been activated. Make sure all
cables are connected properly and the power adapter is connected to a
power source. In addition, check if the emergency button is released. Press
the ON/OFF-button to turn on the system.
The Agrilaser Autonomic wil shut down in case of a power cut.
After loss of power the Agrilaser Autonomic must be switched
on again manually, by pushing the ON/OFF button.
If problems keep occurring after troubleshooting attempts, please contact
your local Agrilaser dealer.
User manual Agrilaser Autonomic
®
EN
NL
FR
DE
ES
PT
IT
14