Installation Requirements; Safety Measures; Beam Protection - BOREAL RADIOFRÉQUENCE Série Instructions D'installation, D'utilisation Et D'entretien

page de 134

/ 134
Matières
Table des Matières
Signets

Table des Matières

Les langues disponibles

Air-flow meter

recommendable that the installation is carried out by people who are qualified and informed about the compliance with the installation and safety norms.

If your equipment is not properly installed, it may cause serious damage.

Before the installation, follow the next verifications:

•

Make sure that the floor can sustain the weight of the equipment and make a proper isolation in the case that it is made of flammable material

(wood) or a material that can be affected by a thermal shock (plaster cast, for example).

•

If the equipment is installed on a floor which is not completely refractory or inflammable such as parquet, carpet, etc, it is necessary to replace this

part or introduce a fire-resistant base so that it protrudes out the oven 30 cm. Example of materials include steel flooring, glass base or any other

type of fire-resistant material.

•

Make sure that there is proper ventilation in the place where it is installed (air intake).

•

Avoid the installation in places where there are collective ventilation pipes, hoods with or without extractor, B type gas equipments, heat pumps or

equipments that can cause that the draw is not good if they are used at the same time.

•

Make sure that the smoke duct and the pipes used for the chimney are suitable for the operation of the device.

•

Make sure that every equipment has their own smoke duct. Do not use the same duct for several equipments.

•

We recommend that you call your fitter in order to check both the chimney as well as the air flow for the combustion.

5.1

SAFETY MEASURES

During the installation of the equipment, there are risks to be taken into account, so you should follow the next safety measures:

Keep any flammable or heat sensitive materials (furniture, curtains, and clothing) at a minimum distance of about 150cm.

If the equipment is installed on a floor which is not completely refractory or inflammable it is necessary to replace this part or introduce a fire-

resistant base.

Do not place the stove near combustible walls or likely to be affected by a thermal shock.

The stove should only be used when the ash pan is inserted and the door closed.

It is recommended to install carbon monoxide detector (CO) in the room where the equipment is installed.

If you need a longer wire than the provided use it always with an earthed plug.

Do not install the stove in a bedroom.

The appliance should never be turned on in the presence of emission of gases or vapours (e.g., linoleum glue, gasoline, etc). Do not place

nearby flammable materials.

Solid combustion residues (ashes) should be collected in an airtight container and resistant to fire.

It is necessary to keep a safe distance when they are installed in spaces where materials are susceptible of being flammables, either the

constructions materials or different materials that surround the stove.

REFERENCES

WARNING!! It is noted that both the stove and the glass

get very hot and should not be touched.

In case of is fire in the stove or smoke duct:

Close the loading door.

Put the fire out by using carbon dioxide extinguishers (CO2 powder).

Request for the immediate intervention of the fire-fighters.

DO NOT PUT OUT THE FIRE WITH WATER

5.2

BEAM PROTECTION

In the Insert 7 model, due to the heat they emit, special attention must be paid to the protection of the beams: when designing your chimney or covering,

take into account, on the one hand, the proximity of the beam to the external faces of the insert and , on the other hand, the radiation of the glass door

that, normally, is very close to the beams themselves. In any case, the inner or lower faces of this beam in combustible material must not be in contact

with temperatures higher than 65ºC.

In the drawing some examples of solution are shown.

FLOW SENSOR (SMART CONTROL)

•

Your stove or insert has a flow sensor placed inside the primary air suction pipe that detects the proper circulation of

combustion air and the smoke exhaust. In case of insufficient air inlet (due to incorrect smoke outlet or improper air

intake), the sensor sends a "block" signal to the stove.

The SMART CONTROL TECHNOLOGY allows a constant combustion by controlling automatically the draft according

to the characteristics of the flue (curves, length, diameter, etc) and the environmental conditions (wind, humidity,

atmospheric pressure, etc).