Jøtul FS 162 Manuel D'installation Et D'utilisation page 23

6. The approval label, which is attached by a wire, is fed under
the burn chamber.
7. Attach the locking bracket (part 8) to the load-bearing plate
using the screws provided (part 32). See fig. 12.
8. Position the lower cover plate (part 9). See fig. 13.
9. Position the side cartridge with stone fitted (parts 10, 11 and
12), fig. 14. Positioning pin with slot must face upwards.
10. Fit upper cover plate (part 13) using the wedges provided (part
14), fig. 15. Fit wedges in towards the centre of the stove.
Fitting with a top outlet
The product is supplied from the factory with smoke outlet fitted
for the top outlet.
• Fit an offset pipe, 60 mm (optional extra).
• Make sure that the gasket is properly seated between the
offset pipe and the smoke outlet.
11. Fit layers 2 and 3 with the relevant brackets.
12. Fit layer 4.
13. Position the two-piece top stone (part 18), Fig. 17.
14. Insert valve plates 1 and 2 (parts 19 + 20). Fig. 18 + 19.
• Thread the flue pipe through the valve plates and place it in
the offset centre pipe.
• Side stones for smoke outlet (parts 16 and 17) should not be
used if using top outlet.
Fitting with a rear outlet at height of 1050 mm
Select stones with holes bored in them for the back stones. Two
of the side stones (part 15) should not be used with rear outlet.
• Use the smoke outlet installed for the top outlet.
• Fit the flue pipe with the smoke outlet on it from the inside of
the burn chamber, then attach the smoke outlet using screws
M8x30mm. NOTE: If the flue pipe is more than 350 mm long,
the flue pipe is pushed into the smoke outlet from the back
of the product. It is important for the joints/flue pipes to be
sealed completely. Air leaks may stop them functioning.
11. Fit layers 2 and 3 with the relevant brackets.
12. Fit layer 4 and additional height if required.
13. Position the two-piece top stone (part 18), Fig. 17.
14. Insert valve plates 1 and 2 (parts 19 + 20). Fig. 18 + 19.
15. Replace the burn plates, baffle, exhaust deflector, inner
bottom, ash pan and riddling grate.
Fitting with a rear outlet at height of 1416 mm
Select stones with holes drilled in them for the rear stones in
layer no. 4. Two of the side stones (part 15) should not be used
with rear outlet.
The product is supplied from the factory with the smoke outlet
fitted for the top outlet.
• Use the smoke outlet installed for the top outlet.
• NOTE: It is important for the joints/flue pipes to be sealed
completely. Air leaks may stop them functioning.
11. Fit layers 2 and 3 with the relevant brackets.
12. Fit layer 4.
13. Fit the flue pipe with a 90
with the instructions from the smoke outlet to the chimney.
(See "4.2 Chimney and flue pipe".
14. Fit additional height if required.
15. Position the two-piece top stone (part 18), Fig. 17.
16. Insert valve plates 1 and 2 (parts 19 + 20). Fig. 18 + 19.
17. Replace the burn plates, baffle, exhaust deflector, inner
bottom, ash pan and riddling grate.
0
bend (not included) in accordance
Fitting with a rear outlet at height of 1781 mm
(with additional height)
Select stones with holes drilled in them for the rear stones in
layer no. 4. Two of the side stones (part 15) should not be used
with rear outlet.
The product is supplied from the factory with the smoke outlet
fitted for the top outlet.
• Use the smoke outlet installed for the top outlet.
• NOTE: It is important for the joints/flue pipes to be sealed
completely. Air leaks may stop them functioning.
11. Fit layers 2 and 3 with the relevant brackets.
12. Fit layer 4 and additional height.
13. Fit the flue pipe with a 90
with the instructions from the smoke outlet to the chimney.
(See "4.2 Chimney and flue pipe".
14. Position the two-piece top stone (part 18), Fig. 17.
15. Insert valve plates 1 and 2 (parts 19 + 20). Fig. 18 + 19.
16. Replace the burn plates, baffle, exhaust deflector, inner
bottom, ash pan and riddling grate.
ENGLISH
0
bend (not included) in accordance
23