Automatic Mode Operation; Removing Air From The Propane Gas Supply Lines; Set The Controls To Automatic Mode Operation; Set The Controls To Manual Mode Operation - Norcold N61X Manuel De L'utilisateur

The selector switch [207] starts and shuts down the refrigerator:
- Push the selector switch to the AUTO position to start the
refrigerator in auto mode.
- Push the selector switch to the GAS position to start the
refrigerator on propane gas.
The temperature switch [142] controls the temperature
adjustment of the freezer and the fresh food compartment. The
temperature adjustment that you select does not change if the
mode of operation of the refrigerator changes.
- Push the temperature switch to the desired temperature
setting.
- The number "5" is the coldest temperature setting.
Refer to the "Display Codes" section of this manual.

Automatic mode operation:

When the refrigerator is in AUTO mode, it automatically uses
the most efficient energy source that is available for operation.
During operation, if a more efficient energy source becomes
available, the refrigerator controls change from the current
energy source to the more efficient energy source as follows:
- The first choice is AC operation if 120 volts AC is available to
the refrigerator.
- The second choice is propane gas operation if 120 volts AC
is not available to the refrigerator.

Removing air from the propane gas supply lines:

For safety reasons, the burner is made to ignite on propane gas
within a specified amount of time. When starting the refrigerator
for the first time, after storage, or after replacing propane gas
tank, the propane gas supply lines can have air in them. Due to
the air in the gas supply lines, the refrigerator may not ignite on
propane gas within the specified amount of time.
To remove the air from the propane gas supply lines:
- Make sure that all of the gas valves are open.
- Push the selector switch to the GAS position and the
refrigerator will start a 30 second trial for ignition.
- During the 30 second trial for ignition, the
refrigerator controls open the gas safety valve and
the igniter sparks.
- During the 30 second trial for ignition, both the ON
and the GAS light show.
- If the ON light [60] and the GAS light [62] both show
after 30 seconds, it means that the refrigerator is
operating on propane gas.
- At this time, all of the air is removed from the
propane gas supply lines and you may select
AUTO mode of operation if you wish.
- If the air in the propane gas supply lines prevents the
burner from igniting on propane gas after 30 seconds
the refrigerator controls close the gas safety valve and
the igniter stops sparking.
- Both the ON light and the GAS light flash about
once every second.
- Push the selector switch to the OFF position and
then to the GAS position and the refrigerator will
start a 30 second trial for ignition.
- Depending on how much air may be in the propane gas
supply lines, you may need to repeat the 30 second trial for
ignition two or three times.
- If the burner does not ignite on propane gas after two or
three attempts, stop and consult your local dealer or an
authorized Norcold Service Center.

Set the controls to automatic mode operation:

Push the selector switch to the AUTO position.
- If 120 volts AC is available to the refigerator, the ON light [3]
shows.
- This means that the refrigerator is operating on AC
electric.
- If 120 volts AC is not available to the refigerator, the ON light
and the GAS light both show.
- This means that the refrigerator is operating on propane
gas.
If the energy source is interrupted:
- The refrigerator shows a fault code.
- Refer to the "Fault Codes" section of this manual.

Set the controls to manual mode operation:

- Push the selector switch to the GAS position.
- When the ON light and the GAS light both show, this means
that the refrigerator is operating on propane gas.
If the energy source is interrupted:
- The refrigerator shows a fault code.
- Refer to the "Fault Codes" section of this manual.
Owner's Manual 5