Manual Flash Mode M; Slave Mode In The Cordless Metz Remote System - Metz MECABLITZ 45 CL-4 digital Basic Mode D'emploi

Setting procedure
• Equip the flash unit with the connecting cable SCA 3045
adapter from the SCA 3002 system and connect to the camera.
• Set TTL on the flash unit with the setting mark for aperture pre-selection
• Switch on the flash unit and the camera.
• Set the camera as explained in the camera's operating instructions.
• Lightly touch the camera's shutter release so that data can be exchanged
between the camera and the flash unit.
• Continue depressing the "Mode" key
given on the indicator window (see subsequent Table 1).
Adapter Camera system
SCA 3102 Canon
SCA 3202 Olympus
SCA 3302 Minolta "Preflash control" / "ADI"
SCA 3402 Nikon
SCA 3402 Nikon i-TTL BL / D-TTL-3D
SCA 3402 Nikon „3D multi-sensor-fill-in flash"
SCA 3402 Nikon „Matrix-controlled fill-in flash"
High-speed synchronisation HSS
The maximum flash range can be read off directly from the aperture calculator
under the f-stop when the ISO value of the camera or film has been manually
set on the flash unit. The shortest shooting distance is approx. 10% of the maxi-
mum flash range. The subject should be located in the middle third of the indi-
cated range to give the electronic circuit leeway for compensation.
The aperture or ISO value does not have to be set on the flash unit for
the TTL flash mode with preflash to function! All flash modes, with the
exception of high-speed synchronisation (HSS), are also supported by
the secondary reflector of the flash unit.
56
and a suitable
3)
until the required flash mode is
Flash modes Display panel
ETTL
E-TTL / E-TTL II
TTL
TTL with preflash
TTL
TTL
i-TTL / D-TTL

6.4 Manual flash mode M

The flash unit emits the full uncontrolled amount of light in the manual mode
if no partial light output has been selected. Adaptation to the photographic
situation may then be achieved with a corresponding aperture setting on the
.
camera.
Setting procedure
• Set the ISO value of the camera or film with the setting knob
head.
• Set the setting mark "M" or manual partial light output (M1/2 - M1/4 –
M1/8 – M1/16 – M1/32) with the setting mark of the selector disk
the flash unit. "M" lights up on the indicator window of the flash unit.
The scale of the aperture calculator indicates, above the given lighting dis-
tance, the aperture that has to be set on the camera.
We recommend the camera mode aperture priority (A, Av) or manual
(M). The adjusted aperture must be corrected when a wide-angle diffu-
ser is used. The setting centre on the flash head automatically takes the
mounted wide-angle diffuser into account.

6.5 Slave mode in the cordless Metz Remote System

TTL BL
When in the cordless Metz Remote System a controller flash unit (40 MZ-...,
TTL BL
50 MZ5, 54 MZ-..., 70 MZ-..., 76 MZ-...) on the camera provides cordless
TTL BL control of light output of one or more slave units in TTL or automatic flash
mode.
HSS
TTL flash modes with preflash (ADI, E-TTL, D-TTL, i-TTL etc.) are not sup-
ported for system-inherent reasons!
The mecablitz 45 CL-4 digital supports the slave mode in the cordless Metz
Remote System. For this purpose, the flash unit must be equipped with a sla-
ve adapter SCA 3083 digital (optional extra). The slave adapter is connec-
ted to the flash unit with the connecting cable SCA 3045
Setting procedure
• Equip the flash unit with the connecting cable SCA 3045
ter SCA 3083 digital.
on the flash
on
.
3)
and slave adap-
3)