Table des Matières
Publicité
• Follow the dust-related national requirements for the
materials you want to work with
• Be careful when cutting grooves, especially in supporting
walls (slots in supporting walls are subject to country-
specific regulations; these regulations are to be observed
under all circumstances)
• Secure the workpiece (a workpiece clamped with
clamping devices or in a vice is held more securely than
by hand)
• Do not clamp the tool in a vice
• Use completely unrolled and safe extension cords with a
capacity of 16 Amps (U.K. 13 Amps)
DURING USE
• Inrush currents cause short-time voltage drops; under
unfavourable power supply conditions, other equipment
may be affected (if the system impedance of the power
supply is lower than 0,25 Ohm, disturbances are unlikely
to occur); if you need further clarification, you may
contact your local power supply authority
• If the cord is damaged or cut through while working, do
not touch the cord, but immediately disconnect the plug
• Never use the tool when cord is damaged; have it
replaced by a qualified person
• In case of electrical or mechanical malfunction,
immediately switch off the tool and disconnect the plug
• In case of current interruption or when the plug is
accidentally pulled out, the tool will not restart on
its own; for restarting the tool unlock the on/off
switch 9c and switch on tool again
AFTER USE
• After switching off the tool, never stop the rotation of the
accessory by a lateral force applied against it
EXPLANATION OF SYmBOLS ON TOOL
2 Read the instruction manual before use
3 Wear protective glasses and hearing protection
4 Double insulation (no earth wire required)
5 Do not dispose of the tool together with household waste
material
WHEN CONNECTING NEW 3-PIN PLUG (U.K. ONLY):
• Do not connect the blue (= neutral) or brown (= live) wire
in the cord of this tool to the earth terminal of the plug
• If for any reason the old plug is cut off the cord of this tool,
it must be disposed of safely and not left unattended
USE
• Mounting of accessories 6
! disconnect the plug
- clean spindle A and all parts to be mounted
- tighten clamping flange B with spanner C while
pushing spindle-lock button D
! push spindle-lock button D only when spindle A
is at a standstill
- for removing accessories handle vice-versa
! grinding/cutting discs become very hot during use;
do not touch them until they have cooled down
! never use a grinding/cutting disc without the label
("blotter") which is glued onto it (if provided)
• Mounting of auxiliary handle E 7
! disconnect the plug
- screw auxiliary handle E on the right, the top, or the left
of the tool (depending on the work to be carried out)
• Removing/mounting/adjusting of protective guard F 8
! disconnect the plug
! ensure that the closed side of the protective
guard always points to the operator
• Before using the tool
- ensure that accessory is correctly mounted and firmly
tightened
- check if accessory runs freely by turning it by hand
- test-run tool for at least 60 seconds at highest no-load
speed in a safe position
- stop immediately in case of considerable vibration or
other defects and check tool to determine the cause
• On/off locking switch J 9
- switch on tool 9a
! be aware of the sudden impact when the tool is
switched on
! before the accessory reaches the workpiece, the
tool should run at full speed
- lock switch 9b
- unlock switch/switch off tool 9c
! before switching off the tool, you should lift it
from the workpiece
! the accessory continues to rotate for a short time
after the tool has been switched off
• Grinding 0
- move the tool back and forth with moderate pressure
! never use a cutting disc for side grinding
• Cutting !
- do not tilt the tool while cutting
- always move the tool in same direction as arrow on
tool head, in order to prevent the tool from being
pushed out of the cut in an uncontrolled manner
- do not apply pressure on the tool; let the speed of the
cutting disc do the work
- the working speed of the cutting disc depends on the
material to be cut
- do not brake cutting discs with side pressure
• Holding and guiding the tool
- always hold the tool firmly with both hands, so you will
have full control of the tool at all times
! while working, always hold the tool at the
grey-coloured grip area(s) @
- provide for a secure stance
- pay attention to the direction of rotation; always hold
the tool so, that sparks and grinding/cutting dust fly
away from the body
- keep ventilation slots K 6 uncovered
APPLICATION ADVICE
• Instead of flange B 6 the "CLIC" quick-clamping flange
(SKIL accessory 2610388766) can be used; grinding/
cutting discs can then be mounted without the use of
accessory keys
• For more tips see www.skil.com
MAINTENANCE / SERVICE
• This tool is not intended for professional use
• Always keep tool and cord clean (especially ventilation
slots K 6)
! do not attempt to clean ventilation slots by
inserting pointed objects through openings
9
Publicité
Table des Matières
