HIKOKI UC 7SL Mode D'emploi page 4

English
GENERAL OPERATIONAL PRECAUTIONS
1. Keep work area clean. Cluttered areas and benches
invite accidents.
2. Avoid dangerous environment. Don't expose power tools
and charger to rain. Don't use power tools and charger in
damp or wet locations. And keep work area well lit.
Never use power tools and charger near flammable or
explosive materials.
Do not use tool and charger in presence of flammable
liquids or gases.
3. This appliance is not intended for use by persons
(including children) with reduced physical, sensory or
mental capabilities, or lack of experience and knowledge,
unless they have been given supervision or instruction
concerning use of the appliance by a person responsible
for their safety.
Children should be supervised to ensure that they do not
play with the appliance.
4. Store idle tools and charger. When not in use, tools and
charger should be stored in dry, high or locked-up place
— out of reach or children. Store tools and charger in a
place in which the temperature is less than 40°C.
5. Don't abuse cord. Never carry charger by cord or yank it
to disconnect from receptacle. Keep cord from heat, oil
and sharp edges.
6. When the charger is not in use or when being maintained
and inspected, disconnect the power cord of the charger
from the receptacle.
7. To avoid danger, always use only the specified charger.
8. Use only genuine HiKOKI replacement parts.
9. Do not use power tools and charger for applications other
than those specified in the Handling Instructions.
10. To avoid personal injury, use only the accessories or
attachment recommended in these handling instructions
or in the HiKOKI catalog.
11. If the supply cord is damaged, it must be replaced by the
manufacture or its service agent or a similarly qualified
person in order to avoid a hazard.
Let only the authorized service center do the repairing.
The Manufacture will not be responsible for any damages
or injuries caused by repair by the unauthorized persons
or by mishandling of the tool.
12. To ensure the designed operational integrity of power
tools and charger, do not remove installed covers or
screws.
SPECIFICATION
CHARGER
Model
Charging voltage
Weight
4
13. Always use the charger at the voltage specified on the
nameplate.
14. Always charge the battery before use.
15. Never use a battery other than that specified. Do not
connect a usual dry cell, a rechargeable battery other
than that specified or a car battery to the power tool.
16. Do not use a transformer containing a booster.
17. Do not charge the battery from an engine electric
generator or DC power supply.
18. Always charge indoors. Because the charger and battery
heat slightly during charging, charge the battery in a
place not exposed to direct sunlight; where the humidity
is low and the ventilation is good.
19. Use the exploded assembly drawing on this handling
instructions only for authorized servicing.
PRECAUTIONS FOR CHARGER
1. Always charge the battery at a temperature of 0 – 40°C.
Charging the battery at temperatures outside the range
of 0 – 40°C may prevent proper charging and reduce
battery life.
The most suitable temperature for charging is that of
20 – 25°C.
2. Do not use the charger continuously.
When one charging is completed, leave the charger for
about 15 minutes before the next charging of battery.
3. Do not allow foreign matter to enter the hole for
connecting the rechargeable battery.
4. Never disassemble the rechargeable battery or charger.
5. Never short-circuit the rechargeable battery.
Short-circuiting the battery will cause a great electric
current and overheat. It results in burn or damage to the
battery.
6. Do not dispose of the battery in fire.
If the battery is burnt, it may explode.
7. Using an exhausted battery will damage the charger.
8. Bring the battery to the shop from which it was purchased
as soon as the post-charging battery life becomes too
short for practical use. Do not dispose of the exhausted
battery.
9. Do not insert objects into the air ventilation slots of the
charger.
Inserting metal objects or flammable into the charger air
ventilation slots will result in an electrical shock hazard or
damage to the charger.
UC7SL
7.2 V
0.35 kg