PLYMOVENT controlGo Manuel D'installation Et D'utilisation page 12

4.4.8 Relay outputs (cable #6 and #7) (options)
Both relay outputs are available for connection to an external
device . Event to activate the relays is:
23
- start/stop fan
attENtioN
- You can choose to connect the cables as NO
(normally open) or NC (normally closed).
- Max. connection: 30 VDC / 2,5 A per relay.
USB
( rmware updates)
Ethernet
Power
(for service only)
Valves Indicator LED's
NO 1 1
Power
Light tower
NC 1 2
COM 1 3
4
1 2 3 4 5 6
NO 2 5
NC 2 6
COM 2 7
8
8
Fig. 4.18 Connection of relay outputs
Power
1 2
4.4.9 LightTower (option)
The light tower contains the same pilot lights as the Panel,
including the buzzer.
Indicator LED's
Light tower
Indicator LED's
Valves Indicator LED's
1 2 3 4 5 6 7
Power
Light tower
Light tower
1 2 3 4 5 6 7
Power
1
Fig. 4.19 Connection of LightTower
IN 1
IN 2
4.4.10 External pressure sensor (option)
IN 3
IN 4
The Panel contains an internal filter pressure sensor.
23. E.g. a roof fan
0000112607/170717/0 ControlGo
Indicator LED's
Valves
Light tower
Digital input 1-5
Filter Pressure
Digital input 6-12
sensor
Valves Indicator LED's
1 2 3 4 5 6 7
Light tower
1 2 3 4 5 6 7
Dustbin Fan Pressure
sensor sensor
Valves
Analog
Filter Pressure
sensor
output
Power
Dustbin Fan Pressure
sensor sensor
Digital input 1-5
1 2 3 4 1 2 3 4
Filter Pressure
Valves
Digital input 6-12
sensor
1 2 3 4 5 6
Analog
Filter Pressure
sensor
output
1 2 3 1 2 3 4
2
BTN start/stop fan
BTN lter cleaning
Service mode switch
Spare
You must use an external pressure sensor
internal one when:
- the distance between the Panel and the filter system MDB or
SCS is more than 10 m; and/or
- the Panel is installed outdoor and the temperature may drop
below 0°C (32°F)
In all other cases the use of an external filter pressure sensor
is optional.
In case of an external pressure sensor:
• Remove the wire bridge from input IN 4 (refer to Fig.
-
+
Dustbin Fan Pressure 4.6A).
sensor
sensor
Analog
Filter Pressure
sensor
output
CAN Slave
Dustbin Fan Pressure
cable #7 sensor sensor
1 2 3 4 1 2 3 4
Power
[page 7]
Analog
Filter Pressure
sensor
output
1 2 3 1 2 3 4
Digital input 1-5
Fig. 4.20 Connection of external pressure sensor
IN 1 BTN start/stop fan
Indicator LED's
IN 2 BTN lter cleaning
-
4.5
IN 3 Service mode switch
+
IN 4 Spare
Digital input 6-12
Light tower
Filter pressure sensor
To monitor the filter pressure, you must connect pneumatic
hoses to the internal filter pressure sensor (+ and –).
Digital input 1-5
CAN Slave
1 2 3 4 5 6 7 8 9 10 11 12
Fig. 4.21
Indicator LED's
• Connect the pneumatic hoses + and – to the corresponding
bulkhead connectors (A).
1 2 3 4 5 6 7 1 2 3 4
• For connection of the pneumatic hoses to the MDB or SCS /
cable #13
EDS filter system, refer to the corresponding manual.
Digital input 6-12
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16
Light tower
1 2 3 4 5 6 7
[page 7]
IN 5 External start/stop signal
IN 6 Fire alarm (ShieldControl)
IN 7 Sliding valve feedback 1
IN 1
IN 8 Sliding valve feedback 2
IN 2
IN 3
Fig. 4.21
IN 4
24. Type PT-2500
For connection of the internal filter pressure sensor,
refer to paragraph 4.5.
Digital input 1-5
Digital input 6-12
Digital input 1-5
Valves Indicator LED's
1 2 3 4 5 6 7 8 9 10 11 12
Filter Pressure
Light tower
sensor
Digital input 6-12
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16
RS485 VFD
IN 5 External start/stop signal
Dustbin Fan Pressure
IN 6 Fire alarm (ShieldControl)
sensor sensor
pneumatic connection
IN 7 Sliding valve feedback 1
IN 8 Sliding valve feedback 2
Also refer to paragraph 4.4.10.
Analog
Filter Pressure
output sensor
RS485 VFD
1 2 3 4 5
Dustbin Fan Pressure
sensor sensor
1 2 3 4
Analog
Filter Pressure
output sensor
1 2 3 1 2 3 4
IN 9 Fan alarm
IN 10 Compressed air switch
IN 11 External alert
BTN start/stop fan IN 5
IN 12 Dustbin level switch
BTN lter cleaning IN 6
Service mode switch IN 7
Connection of pneumatic hoses to the Panel
Spare IN 8
instead of the
24
RS485 VFD
Filter pressure
-
(internal sensor)
-
+
+
Fan pressure
-
(internal sensor)
+
RS485 VFD
Digital input 1-5 CAN Slave
1 2 3 4 5
RS-232
Digital input 6-12
(for service only)
cable #9
[page 7]
CAN Slave
IN 9 Fan alarm
Digital input 1-5
IN 10 Compressed air sw
IN 11 External alert
IN 12 Dustbin level swit
CAN HMI
Digital input 6-12
CAN Slave
1 2 3 4 5
Digital input 1-5
1 2 3 4 5 6 7 8 9 10 11 12
CAN HMI
1 2 3 4 5
A Filter Pressure
Digital input 6-12
1 2 3 4 5 6 7 8 9 10 11 12 13 14
External start/stop signal
Fire alarm (ShieldControl)
Sliding valve feedback 1
Sliding valve feedback 2
EN - 11
1
1
1
IN 9 F
IN 10 C
IN 11 E
IN 12 D