Stanley IntelliLaser Pro Mode D'emploi page 3

Niveau laser/détecteur de structure
Masquer les pouces Voir aussi pour IntelliLaser Pro:
Table des Matières

Publicité

Les langues disponibles
  • FR

Les langues disponibles

  • FRANÇAIS, page 10
• ALWAYS use only accessories that are recommended by the manufacturer for you model. Accessories
that may be suitable for one laser may create a risk of injury when used on another laser.
• DO NOT remove or deface warning labels. Removing labels increases risk of laser radiation.
• DO NOT disassemble, service or repair this product. Repairs performed by unqualified personnel could
result in serious injury.
• DO NOT direct the laser beam toward aircraft or moving vehicles.
• DO NOT project laser beam onto a reflective surface.
• DO NOT splash or immerse the unit in water.
• ALWAYS turn off the product when not in use.
• ALWAYS ensure battery is inserted in the correct manner, with the correct polarity.
• NEVER intentionally short any battery terminals.
• DO NOT attempt to charge alkaline batteries.
• DO NOT dispose of batteries in fire.
• ALWAYS remove the battery if storing the unit for over a month.
• DO NOT dispose of this product with household waste.
• ALWAYS check local codes and properly dispose of used batteries.
• PLEASE RECYCLE in line with local provisions for the collection and disposal of electrical and electronic
waste.
WARNING: Carefully read the User Safety and Operating Instructions before using this
product. The person responsible for the instrument must ensure that all users understand and adhere to
these instructions.
WARNING: The following labels are placed on the laser tool to inform you of the laser class for your
convenience and safety.
IEC/EN 60825-1 Complies with 21 CFR 1040.10 and 1040.11 except for deviations pursuant to Laser Notice
No. 50, dated June 24, 2007
Max Output <1 mW @ 630 - 690 nm
The IntelliLaser
Pro produces a straight line on the same surface on which the tool is placed. Any reflection
TM
of the line on another surface should be considered a reference.
OPERATING INSTRUCTIONS
BATTERY
Open the battery door on the back of unit and connect a 9-volt battery to the clip. Place battery back into
case and snap the battery door on. It is recommended to replace 9 volt battery with a new battery when low
battery indicator is on.
USAGE
Detecting Wood / Metal Studs
Note: Laser line is always on when holding the activation button.
1) Hold the IntelliLaser
button
Note: The unit cannot be moved before calibration is complete.
• When the "READY" icon is displayed the unit is calibrated.
• Keep holding the activation button during all of the following procedures.
Note: Once the activation button is released, the unit shuts off.
• If the "READY" icon is not displayed after approximately 10 seconds, move the IntelliLaser Pro to
a different location and try again. Releasing the activation button will turn off the sensor.
Note: While calibrating the IntelliLaser
metal, or over a wet or newly painted area, or it will not properly calibrate.
• Slide the IntelliLaser
display will gradually fill.
2) When it detects the stud edge, the "EDGE" icon will be displayed and an audible tone will sound. Use
the laser line emanating from the top of the unit to mark the stud edge.
3-4) Repeat the above steps from the other side of the stud. Coming from the opposite direction, mark the
other edge of the stud.
• The midpoint of the two marks indicates the stud center.
IEC60825-1: 2014
Pro flat against the surface, making firm contact. Depress and hold activation
TM
Pro must not be placed directly over a stud, dense material such as
TM
Pro slowly across the surface in a straight line. As it detects a stud, the target
TM
LASER
LASER
1
GB
3

Publicité

Table des Matières
loading

Ce manuel est également adapté pour:

Intellilaser pro 0-77-260

Table des Matières