Table des Matières
Publicité
Les langues disponibles
Les langues disponibles
Adjustments and settings in the menu (continued)
Select cursor
Clear Motion Drive
Off
Mode 1
Mode 2
Mode 3
Mode 4
Film Motion
CMD Demo
Left
Right
Top
Bottom
Off
MPC Level
65 55
Lens Aperture
Lamp Power
Normal
High
Picture Adjust
User Name Edit
>>
Name
User 1
A
B
C
D
E
F
N
O
P
Q
R
S
a
b
c
d
e
f
n
o
p
q
r
s
1
2
3
4
5
6
!
"
#
$
%
&
:
;
~
|
(
)
SPACE
Clear
Operate
Exit
MENU
Select
It improves video images with fast movements to produce clear video images with little
residual image retention.
This cannot be set when the PC Signal/3D Signal and "[2-3] 2D/3D" are ON.
Moreover, it may happen that the image is distorted in some scenes, or light and dark
flashes occur. In this case, please choose "Off", etc., and then a setting of your choice.
Settings: Off, Mode 1, Mode 2, Mode 3, Mode 4, Inverse Telecine
Off
Black insertion weak
Black interpolation strong
Interpolation weak
Interpolation strong
With 60i/60p signals, e.g of TV-broadcast and DVDs, original 24 frame video image
footage is changed to a 24 frame display.
(*) 24p will not function.
It is possible to confirm the effect of the setting of Mode 3 and Mode 4 of the Clear motion
drive. Upon pressing the button "OK", it will be displayed on all sides of a screen in the
center split into two parts. Finally, it will turn to "Off". It cannot be set for PC and 3D
signals.
Settings: Left, right, top, Bottom, Off
The left screen displays a demonstration of the Clear motion drive.
The right screen displays a demonstration of the Clear motion drive.
The upper screen displays a demo of the Clear motion drive.
The screen below displays a demo of the Clear motion drive.
The Demo of the Clear motion drive is turned off.
Adjust the effect of resolution sense caused by increase in resolution of image display.
Please adjust the image noise according to your requirement.
(*) When the "picture mode" is "film" and "THX", the default value will be "1".
(*) Cannot adjust if input signal is 3D or "2D to 3D conversion" is "ON".
(*) Cannot adjust when the setting of "Clear Motion Drive" is "Mode 1" or "Mode 2".
Settings: 0 to 3
Adjusts the amount with which the optical iris is squeezed. A setting of 0 means fully
opened.
Settings: (Dark) -15 to 0 (bright)
It is possible to change the brightness of the lamp.
(*) If continually used with "High", the lamp will become dark earlier.
(*) The more one lets the interior temperature of the device rise due to generation of heat,
the less the level of tolerance against high temperatures.
(*) For about 60 seconds after the lamp is lit, the lamp cannot be switched off.
(*) This will be "High" when the "Picture Mode" is set to "3D".
(*) This will be "High" when the "Picture Mode" is set to "3D", "Film" and "Cinema".
Settings: Normal, High
Normally this setting is chosen.(160W drive)
In a bright room, when the video is hard to see, this setting is chosen.(220W drive)
G
H
I
J
K
L
M
T
U
V
W
X
Y
Z
g
h
i
j
k
l
m
t
y
v
w
x
y
z
7
8
9
0
,
.
^
*
+
-
/
=
?
@
<
>
[
]
{
}
\
All Clear
OK
Back
BACK
ENGLISH
Input cursor
Character list
[Off]
[Off]
[2]
[0]
65 55
X7
45
[Normal]
57
Publicité
Chapitres
Table des Matières
Dépannage
