Table des Matières
Publicité
Les langues disponibles
Les langues disponibles
Installation and Operating Instructions
1/3" Day & Night Board Camera VKC-1373/VAR210
1. Safety Instructions
• Read these safety instructions and the operation manual first before you install and commission the camera.
• Keep the manual in a safe place for later reference.
• Protect your camera from contamination with water and humidity to prevent it from permanent damage.
Never switch the camera on when it gets wet. Have it checked at an authorized service center in this case.
• Never operate the camera outside of the specifications as this may prevent the camera functioning.
• Do not operate the cameras beyond their specified temperature, humidity or power ratings.
Operate the camera only at a temperature range of -10°C to +50°C and at a humidity of max. 90%.
• To disconnect the power cord of the unit, pull it out by the plug. Never pull the cord itself.
• Pay attention when laying the connection cable and observe that the cable is not subject to heavy loads, kinks,
or damage and no moisture can get in.
• The warranty becomes void if repairs are undertaken by unauthorized persons.
Do not open the camera housing.
• Never point the camera towards the sun with the aperture open. This can destroy the sensor.
• Installation, maintenance and repair have to be carried out only by authorized service centers.
Before opening the cover disconnect the unit from mains input.
• The fitter is responsible for the system of protection being followed in accordance with the technical data,
e.g. by sealing of the cable outlet with silicone.
• Contact your local dealer in case of malfunction.
• Only use original parts and original accessories from Videor E. Hartig GmbH.
• Do not use strong or abrasive detergents when cleaning the dome. Use a dry cloth to clean the surface.
In case the dirt is hard to remove, use a mild detergent and wipe gently.
NOTE: This is a class A digital device. This digital device can cause harmful interference in a residential
area; in this case the user may be required to take appropriate corrective action at his/her own
expense.
2. Product information
Most CCD Colour cameras, even of high quality, show very poor performance when they are working under strong
backlight conditions. However, by using of Double Speed Sony CCD (Progressive Scan) and SS-2 chip set, as in the
VKC-1334/VAR49, this problem will be solved. The Double Speed CCD reads both bright and dark areas separately
at the same time and after that the different exposures will be combined to one image by the Wide Dynamic chip
CX3151. That's why, even though there it is very bright light or spotlights on the object, the picture will remain very
sharp without any blooming and smear. Furthermore true Day and Night function, using a removable IR cut filter
and a day/night lens with no focus shift, a real 24hrs. monitoring with clear image both at day and night can be
realized, if the camera was optimized according to the application.
2.1 Main Features
• Sony Progressive Scan Interline Transfer CCD
• Wide Dynamic Function (WDR, 60dB)
• Resolution of 560 Horizontal Lines (at Colour)
• Sensitivity of 0.01Lux at F1.2 (16x DSS/B&W)
• On-screen Menu Control / Camera Title Display
• Removable IR Cut Filter
• Automatic White Balance (ATW/AWB)
• High and Low Speed Shutter Control (ESC/DSS)
• Digital Zoom 2x-16x
• 4 Privacy Zones adjustable
• External Day/Night Selection
• RS-485 Interface
• Supply Voltage: 12VDC
3. Pinout and DIP Switch Settings
Voltage supply and video connection (J205)
Pin Name
IN/OUT
Colour
1
VIDEO
Output
Blue
BNC
2
GND
Green
3
DC 12V
Input
Yellow
4
AD KEY
Input
Orange
5
GND
Red
6
RXD
Brown
7
TXD
Black
Day-night switching and IR-LED control (J206)
Pin Name
IN/OUT
Colour
1
NC
2
NC
3
NC
4
NC
5
NC
6
NC
7
EXT
Output
White
8
IR_ON
Output
White
9
CDS_IN
Input
10
GND
DC Iris Control (J204)
Pin DC IRIS
LEVEL
1
DAMP +
2
DAMP –
3
DRIVE +
4
GND
4. Menu Configuration
GENERAL DZOOM
OFF, x2~x16
POSI / NEGA
NEGA / POSI
HR MODE
OFF, 1~7
SHARPNESS
0~15
MIRROR
NORMAL, MIRROR,
VERTICAL, ROTATE
OFF, ON
FREEZE
INITIAL
ON, OFF
EXIT
AWB
WB MODE
AUTO, HOLD, USER, CRS
RED CONT
NOT USE (AUTO, HOLD,
CRS), 1~255 (USER)
BLUE CONT
NOT USE (AUTO, HOLD,
CRS), 1~255 (USER)
NOT USE (AUTO, USER.
PUSH AUTO
CRS), OFF/PUSH (HOLD)
INITIAL
ON, OFF
EXIT
AE
BRIGHTNESS
0~60 (ELC, DC),
NOT USE (VIDEO)
FLICKERLESS NOT USE (ELC), ON/OFF
(DC, VIDEO)
SHUTTER SPD NOT USE (ELC), OFF,
x250~x10000 (DC, VIDEO)
AGC MAX SET NOT USE (D&N AUTO),
OFF, LOW~HIGH (DAY,
NIGHT, EXT)
MAX FLD SET OFF, 2FLD~20FLD,
40FLD, 80FLD, 160FLD
INITIAL
ON, OFF
EXIT
D & N
AUTO, DAY, NIGHT,
D/N MODE
EXIT, CDS
LEVEL
AUTO: MID, HIGH
EXT: NOT USE
CDS: 1~5
Notes
1.0Vp-p at 75ohms
9-15V (12V ±0.5V recommended)
Menu control
Notes
D&N switching (ON: GND, OFF: OPEN)
External IR-LED control (+5V switch output)
CdS Sensor
Day & Night Switch (J208)
Pin DC IRIS
LEVEL
1
MOTOR –
2
MOTOR +
D & N
FILTER DLY
0~15 SEC
BURST
ON, OFF
INITIAL
ON, OFF
EXIT
WDR
OFF, ON, AUTO
WDR MODE
WDR LEVEL
0~15
OFF, ON
BACK LIGHT
BLC LEVEL
O~15
INITIAL
ON, OFF
EXIT
PRIVACY
1~4
AREA
MASK
ON, OFF
START X
END X
START Y
END Y
INITIAL
ON, OFF
EXIT
MDT
DETECT AREA LOW, CENTER, LEFT,
RIGHT, WHOLE, UP
DETECT MODE OFF, ON
SENSITIVITY
0~15
INITIAL
ON, OFF
EXIT
COMM
ID DISPLAY
ON, OFF
CAMERA ID
000~255
ZONE DISP
ON, OFF
ZONE LABEL
SET
PROTOCOL
DET, P/D
VERSION
VER
INITIAL
ON, OFF
EXIT
INITIAL
OFF STATE
ON, OFF
EXIT
Publicité
Table des Matières
