Additional Information; Troubleshooting - PIONEER DJ XDJ-RR Mode D'emploi

Additional information

Troubleshooting

! Improper operation is often mistaken for trouble or a malfunction that occurred in the device. If something is wrong with this unit, check the follow-
ing issues, and also access the following Pioneer DJ support site and check [FAQ] for [XDJ-RR].
pioneerdj.com/support/
Some problems occur due to the connected components. If the problem cannot be resolved after checking the connected components, contact the
service center or your dealer for repairs.
! The unit may not operate properly due to static electricity or other external influences. In such cases, disconnect the power cord and connect it
again to restore normal operation.
Power supply
Problem
The unit does not turn on.
The indicators do not light up.
The power suddenly turns off.
Audio output
Problem
Sound is not output, or sound is too
small.
Sound is distorted.
Sound is not output, or the output
sound is distorted or noisy.
Microphone sound is not output or
the volume is low.
Display
Problem
Playing address is not displayed in the
remaining time display.
The category is not displayed.
The scale is not displayed.
The enlarged waveform is not
displayed.
Functions and operations
Problem
The crossfade function does not work.
The back cue function does not work.
Beat effect does not work.
Color effect does not work.
The SYNC function does not work.
Check
Is the power cord properly connected?
Is the [u] switch turned on?
Is the auto standby function activated?
(When auto standby is functioning, the
[MASTER REC (WAKE UP)] button is lit in red.)
Check
Are the [TRIM] control, channel faders, crossfader
and [MASTER LEVEL] control set to the proper
positions?
Is the [MASTER LEVEL] control set to the proper
position?
Is the [TRIM] control set to the proper position?
Is the level of sound input to the [MIC] terminal set
to an appropriate level?
Is this unit placed near a TV?
Is the [MIC LEVEL] control set to the proper
position?
Is the switch on this unit or the microphone
turned off?
Check
—
Is the rekordbox library information stored on the
USB device?
Is the USB device write-protected?
Is the track over 15 minutes long?
Is the track over 60 minutes long?
Check
Is the [CROSS FADER CURVE (THRU,
(crossfader curve selector) switch set to [THRU]?
Is a cue point set?
Is the [LEVEL/DEPTH] control set to the center
position?
Is the [TRIM] control set to the proper position?
Is the [SOUND COLOR FX
(DUB ECHO, PITCH, NOISE, FILTER)] button
pressed?
Is the [COLOR] control set to the proper position?
Has the music file been analyzed?
Remedy
Connect the power cord to an AC outlet. (page 9 )
Turn on the [u] switch.
This unit is shipped with the auto standby function set to on. If you do not
want to use the auto standby function, set [AUTO STANDBY] to [OFF] on the
[UTILITY] screen.
Remedy
Set the [TRIM] control, channel faders, crossfader and [MASTER LEVEL] control
to the proper positions. (page 12 )
Adjust the [MASTER LEVEL] control so that the master channel level indicator
lights around [0 dB] at the peak level.
Set [ATT.] of [MASTER OUT] on the [UTILITY] screen to [-6 dB] or [-12 dB].
Adjust the [TRIM] control to confirm that the channel level indicator lights up in
orange at the highest volume. (page 12 )
Set the [MIC LEVEL] control to the proper position.
Turn the TV off, or place this unit farther away from the TV.
Set the [MIC LEVEL] control to the proper position.
Turn the switch on.
Remedy
Playing address may not be displayed for files recorded in VBR. This happens
when it takes time for the unit to detect the length of the track and display the
playing address.
Use a USB device containing the library information that is exported from
rekordbox to the device..
Disable write-protection on the USB device to make it writable.
The scale is not displayed for tracks whose playing time is over 15 minutes.
The enlarged waveform is not displayed for tracks whose playing time is over 60
minutes.
Remedy
, )] Set the [CROSS FADER CURVE (THRU,
switch to a position other than [THRU]. (page 12 )
Set a cue point.
Rotate the [LEVEL/DEPTH] control clockwise or counterclockwise.
Set the [TRIM] control to the proper position.
Press the [SOUND COLOR FX (DUB ECHO, PITCH, NOISE, FILTER)] button.
Set the [COLOR] control to the proper position.
Perform file analysis.
, )] (crossfader curve selector)
En
13