Button Volume; Factory Setting - Thermador DWHD770W Serie Notice D'utilisation

Auto power off
This setting determines the length of time the control
panel stays illuminated after the cycle is complete.
To save energy, the recommended setting is "after one
minute".
Possible settings are:
off: The appliance does not switch off automatically.
▯
After one minute: The appliance switches off after
▯
1 minute. This is the most energy efficient setting.
After two hours: The appliance switches off after
▯
2 hours.
Tone volume
The end of the wash cycle is indicated by a buzzer. You
can also change this setting.

Button volume

When you are operating the dishwasher, a signal sounds
whenever a button is pressed. You can control the
volume of the signal. If you do not like the button volume,
you can switch it off.
Greeting
When you switch on the dishwasher, the brand logo
appears. You can switch off the brand logo.

Factory setting

You can reset all settings to the factory setting.
Switching the appliance on
1. Turn the water supply on fully.
2. Open the door.
Switch on On/Off switch
3.
The Auto wash cycle has been preset as a default
whenever the appliance starts. This wash cycle
remains selected if no other wash cycle button
pressed.
)*
4. Press Start button
5. Close the door.
Wash cycle sequence starts.
Note: Your dishwasher is protected against unintentional
operation. If the appliance door remains open for more
than 4 seconds after pressing the Start button, the
operation will be paused. Press the Start button again
and close the appliance door.
32
(
.
0
.
Delay start time
You can delay the start of the wash cycle by up to
24 hours. Depending on the setting of the time display,
the end of cycle is indicated with "Finish in" (for example
3h 25m) or "Finish at" (for example 15:20 hours).
Open the door.
1.
2. Switch on On/Off switch
3. Select wash cycle
Press Delay start button
4.
Keep pressing the setting buttons + -
5.
displayed time corresponds with your requirements.
Press Start button
6.
activated.
To delete the Delay start time, press Start button
7.
for about 3 seconds.
Close the door.
8.
Note: Your dishwasher is protected against unintentional
operation. If the appliance door remains open for more
than 4 seconds after pressing the Start button, the
operation will be paused. Press the Start button again
and close the appliance door.
Sapphire Glow (emotionLight™) *
The Sapphire Glow (emotionLight™)
door is open irrespective of whether the On/Off switch
(
is switched on or off. When the door is closed, the
emotionLight™ is off. You can switch the EmotionLight on
or off.
Note: Note that when the door is open the
emotionLight™ is automatically switched off after 1 hour.
Star Glow (emotionLight Pro™) *
1"
emotionLight™
dishwasher. You can switch the interior lighting on or off.
Once you have switched on emotionLight™, you can
select other settings.
is
Possible settings are:
emotionLight™ is on when the door is open and off
▯
when the door is closed.
emotionLight™ 1 (brightness setting for interior
▯
lighting):
In the setting emotionLight™ 1 you can adjust the
brightness of the interior lighting in 4 levels.
emotionLight™ 2 (color setting of interior lighting):
▯
In the setting emotionLight™ 2 you can select a color
for the interior lighting. With the Home Connect™ app,
you can create a custom color.
emotionLight™ 3 (visual signaling of faults):
▯
In the setting emotionLight™ 3 you can switch the
visual indication of a fault on or off. If you have
switched on emotionLight™ 3 and a fault occurs on
your dishwasher, the interior lighting will flash.
Notes
Note that the interior lighting is automatically switched
▯
off after 1 hour when it is switched on and the door is
open.
(
.
0
.
`
.
X
)*
, timer programming is
1"
is on when the
is the interior lighting for your
until the
)*