Inspecting The Press Tool And Attachments - RIDGID ProPress Fitting System Manuel De L'opérateur

1 1 / " rings can be actuated with either a V1 actuator and
4
Standard Series Press Tools such as the CT-400, 320-E,
RP 330 or RP 340, or a C1 actuator and Compact Series
Press Tools such as the 100-B, RP 200 and RP 210. 1
and 2" rings can only be actuated with the V2 actuator and
Standard Series Press Tools. 1
cannot be actuated with Compact Series Press Tools.
The ProPress rings must be used perpendicular to the fit-
ting and tube being pressed but the ball pocket/tip feature
on the rings and actuators allows the actuator and press
tool to swivel up to 90 degrees in each direction. This
allows the rings and actuators to be used in some appli-
cations where the jaw sets and pressing tool will not fit.
The ProPress rings are marked to show the correct actu-
ator for use with that ring.
Catalog No. Description
27998 1 / " ProPress Ring
2
28003 3 / " ProPress Ring
4
28008 1" ProPress Ring
28013 1 1 / " ProPress Ring
4
28018 1 1 / " ProPress Ring
2
28023 2" ProPress Ring
26163 C1 Actuator
28033 V1 Actuator
21878 V2 Actuator
Figure 3 – ProPress Ring and V2 Actuator
ProPress XL-C
RIDGID makes ProPress XL-C Rings for use with ProPress
XL-C Fittings. ProPress XL-C Rings are de signed to
mechanically press ProPress XL-C fittings onto 2
4" tubing. An individual ring is required for each tubing
size. ProPress XL-C Rings are actuated with V2 actuators
and Standard Series Press Tools such as the CT-400,
320-E, RP 330 or RP 340. ProPress XL-C Rings cannot be
used with the Compact Series Press Tools.
The ProPress XL-C rings must be used perpendicular to
the fitting and tube being pressed but the ball pocket/tip
1 / "
2
1 / " and 2" ProPress rings
2
Weight
0.50 lbs (0,23 kg)
0.70 lbs (0,32 kg)
0.90 lbs (0,41 kg)
1.00 lbs (0,45 kg)
1.35 lbs (0,61 kg)
2.00 lbs (0,91 kg)
2.10 lbs (0,95 kg)
4.80 lbs (2,18 kg)
4.7 lbs (2,13 kg)
1 / ", 3" and
2
ProPress ® Fitting System
feature on the rings and actuators allows the actuator
and press tool to swivel up to 90 degrees in each direction.
Catalog No. Size
20543 2 1 / " XL-C Press Ring
2
20548 3" XL-C Press Ring
20553 4" XL-C Press Ring
21878 V2 Actuator
21103 Carrying Case
XL-C Press Ring
Press Ring Actuator
Pivot Pin &
Pocket (Not Visible)
Torsion Spring
(Not visible)
ProPress XL-C Press Ring
Figure 4 – ProPress XL-C Press Ring and RIDGID V2
Actuator
Only use RIDGID Press Tools and RIDGID
WARNING
press tool attachments (jaw sets, rings, actuators, etc.)
when specified by the fitting manufacturer for use with their
system. Use of incorrect press tools and/or attachments for
a system can cause system leaks, damage the press
tool or attachment, void warranties or cause severe per-
sonal injury.
Contact the fitting manufacturer for specific
NOTI E
information on their system, including compatible tubing,
materials, installation instructions, minimum distance be -
tween fittings, seal material, inspection, testing, etc. Incor -
rect installation can cause system leaks and extensive
property damage.
Contact Ridge Tool Technical Service Department at
(800) 519-3456 or rtctechservices@emerson.com for a list
of press fitting system and valve manufacturers that spec-
ify RIDGID pressing tools and attachments for their sys-
tems.
Inspecting the Press Tool and
Attachments
WARNING
Inspect your pressing tool and attachments daily
Weight
5.46 lbs (2,48 kg)
9.63 lbs (4,37 kg)
11.08 lbs (5,03 kg)
6.71 lbs (3,04 kg)
6.15 lbs (2,79 kg)
V2 Actuator
V2 Actuator
Spherical Tip Arm
V2 Side
Plate
V2 Actuator Torsion
Spring (Not Visible)
RIDGID V2 Actuator
3