Table des Matières
Publicité
Les langues disponibles
Les langues disponibles
Protocol
Set the protocol to either Art-Net™ or sACN:
1.
Select the DMX Port to configure as instructed in
2.
Use the knob to select 4. Protocol.
3.
Press the knob.
4.
Use the knob to select the desired settings from ArtNet or sACN.
5.
Press the knob.
Framerte/fs
The frame rate, in milliseconds (ms), is the speed at which the DMX packets are sent out of the 8 DMX
ports. This only applies when the ports are set to Output.
1.
Select the DMX Port to configure as instructed in
2.
Use the knob to select 5. Framerte/fs.
3.
Press the knob.
4.
Use the knob to set the frame rate from 010–040.
5.
Press the knob.
This feature is useful for fixtures unable to receive high speed DMX.
Network
To set the net setting, do the following:
1.
Select the DMX port to configure as instructed in
2.
Use the knob to select 6. Network.
3.
Press the knob.
4.
Use the knob to select from range options (differs based on Disp Type and Protocol selections):
•
000–127: When Disp Type is set to DEC & Protocol is set to ArtNet.
•
001–128: When Disp Type is set to DEC & Protocol is set to sACN.
•
00H–7FH: When Disp Type is set to HEX & Protocol is set to ArtNet.
•
01H–80H: When Disp Type is set to HEX & Protocol is set to sACN.
5.
Press the knob.
This is implemented in very few consoles and only applies to the ArtNet 4 protocol.
1st Universe
Sets the primary Input/Output universe. When using HTP/LTP signal merging, and operating in Output
mode, this will work in unison with the 2nd universe setting to merge data from 2 different IP addresses.
1.
Select the DMX port to configure as instructed in
2.
Use the knob to select 7. 1st Universe.
3.
Press the knob.
4.
Use the knob to select from range options (differs based on Disp Type and Protocol selections):
•
000–255: When Disp Type is set to DEC & Protocol is set to ArtNet.
•
001–256: When Disp Type is set to DEC & Protocol is set to sACN.
•
00H–7FH: When Disp Type is set to HEX & Protocol is set to ArtNet.
•
01H–80H: When Disp Type is set to HEX & Protocol is set to sACN.
5.
Press the knob.
2nd Universe
Sets the secondary Output universe. When using HTP/LTP signal merging, and operating in Output mode,
this will work in unison with the 1st universe setting to merge the data from 2 different IP addresses.
1.
Select the DMX port to configure as instructed in
2.
Use the knob to select 8. 2nd Universe (option will only display if DMX Status is set to OUTPUT
& DMX Mode is set to HTP or LTP).
3.
Press the knob.
4.
Use the knob to select from range options (differs based on Disp Type and Protocol selections):
•
000–255: When Disp Type is set to DEC & Protocol is set to ArtNet.
•
001–256: When Disp Type is set to DEC & Protocol is set to sACN.
•
00H–7FH: When Disp Type is set to HEX & Protocol is set to ArtNet.
•
01H–80H: When Disp Type is set to HEX & Protocol is set to sACN.
5.
Press the knob.
16
Set DMX
Port.
Set DMX
Port.
Set DMX
Port.
Set DMX
Port.
Set DMX
Port.
Net-X II User Manual Rev. 3
Operation
Publicité
Table des Matières
