Table des Matières
Publicité
Les langues disponibles
Les langues disponibles
ENGLISH
18
General safety instructions for
mounting xtures
WARNING Read all safety instructions and
directions supplied with the mounting xture
or power tool. Failure to follow the warnings and
instructions may result in electric shock, re and/or
serious injury.
Save all warnings and instructions for future
reference.
Disconnect the plug from the socket and/or remo-
ve the battery before adjusting the equipment or
replacing accessories. Some accidents are caused by
power tools starting up unintentionally.
Before assembling the power tool, install the
mounting device properly. Correct assembly is
important in order to avoid the risk of collapsing.
Fasten the power tool securely to the mounting
xture before using it. If the power tool slips on the
mounting xture, this can lead to a loss of control.
Place the mounting xture on a rm, level and
horizontal surface. If the mounting xture is unsta-
ble, the power tool cannot be steered smoothly and
safely.
Do not overload the mounting xture and do
not use it as a ladder or sca olding. Overloading
or standing on the mounting xture can cause the
centre of gravity of the mounting xture to move
upwards and cause it to tip over.
Additional Safety and Working
Instructions
Be sure to pay attention to the operating instruc-
tions for the attached router.
Always use the appropriate table feed rings relevant
to the size of the milling tool.
Use protective equipment. Always wear safety
glasses when working with the machine. The use of
protective clothing is recommended, such as dust
mask, protective gloves, sturdy non-slip footwear and
ear defenders.
Wear ear protectors. Exposure to noise can cause
hearing loss.
The dust produced when using this tool may be
harmful to health. Do not inhale the dust. Use a dust
absorption system and wear a suitable dust protec-
tion mask. Remove deposited dust thoroughly, e.g.
with a vacuum cleaner.
Wear tight- tting gloves at all times when hand-
ling sharp blades and saw blades,
Warning against thrown-o items
Always wear goggles when using the machine.
Warning against hand injury / bruising
Never reach into the danger area of the machine
when it is running. Always use the protective shields
on the machine.
Chips and splinters must not be removed while the
machine is running.
Kickback is the sudden reaction caused by loss of
control in guiding small workpieces. Pinching or
snagging causes rapid stalling of the rotating wheel
which in turn causes the uncontrolled power tool
to be forced in the direction opposite of the wheel's
rotation at the point of the binding.
Always use horizontal pressure devices when working
on narrow workpieces. Uncontrolled tilting of the
workpiece can cause a dangerous situation.
The device must not be used for arc milling.
Incorrect use of milling tools, workpieces and
devices for workpiece guidance can lead to a dan-
gerous situation. The operator must be adequately
trained in the handling of the workpiece, the use,
adjustment and operation of workpiece clamping
devices and workpiece guiding devices as well as the
selection of the milling tools.
Tools that are not regularly serviced can trigger
uncontrollable situations. Use only sharp, well-
serviced milling tools set according to the machine
manufacturer's speci cations.
Keep body parts and clothes away from rotating
parts of the device.
Pull the plug out of the socket and/or remove the
battery when the tool is not in use before you make
machine settings or change accessories, such as the
saw blade, drill bit or cutter. This safety measure pre-
vents unintentional starting of the electric tool.
Keep your hands on the fence during milling. Use
pressing devices (printing shoes) in conjunction with
the fence whenever possible.
Missing lateral fences can cause kickback. When
inserting the milling machine, use the rear and/or
front lateral fences attached to the milling fence.
The cutter must be correctly clamped in the machine.
Only move the workpiece in counter rotation to
cutter (only work oppositely oriented)! For security,
use devices such as safety- and pressure device, guide
slide, rip fence, etc.
Set the speed to suit the material you wish to cut.
Only use tools whose permitted speed is at least as
high as the highest no-load speed of the machine.
Provide adequate support such as table extensions,
saw horses, etc. for a workpiece that is wider or longer
than the table top.
Put the router back to original position after usage
(loosen clamping lever to secure cage).
Publicité
Table des Matières
