Télécharger Imprimer la page

Güde GLS 2500 G Mode D'emploi Original page 10

Publicité

Les langues disponibles
  • FR

Les langues disponibles

  • FRANÇAIS, page 11
Transportation and Storage
For a longer shut-down, unplug the unit and store it so that
it is not accessible for children. Keep it in a dry and safe
place.
Assembly and Initial Operation
The vac has to be assembled correctly for the
handling with the leaves vas to be safe and
efficient. Kindly observe the following instructions of
assembly.
Suction-blowing tube assembly
Pull out the tube to the stop from the unit
(Fig. 2). Then fasten the suction adapter with screws
at both the sides included in the delivery (there are
holes in the suction tube ) (see Fig. 3)
1. Fitting the leaves collection bag
To fit the collection bag, push the collection bag neck
in the end of tube at the bottom of the unit. Push the
locking hooks together slightly and push the neck
inside to snap (Fig. 6). Now, hook the leaves
collection bag in the suspension device (Fig. 7)
Do not attempt operating the unit without
the suction adaptor!
Initial Operation Safety Instructions
Plug the unit in it being switched off .
Procedure
Assemble the parts in sequence indicated . Make sure that
the structural parts are arranged correctly according to
figures.
Operation
1. Pick Up Function
If you wish to use the unit for picking up, make sure
that the collection bag is fitted on correctly. Then
plug the unit in. Put the carry strap over your
shoulder and adjust its length. Place the control
lever in the position marked „Saugen" (suction).
Place the suction tube in the working position in
front of you so that it is on the transport wheel.
When the collection bag is full, the suction capacity
decreases. If that happens, switch the unit off and
unplug it. Wait for the motor to come to standstill
completely. Remove the bag according to
description above. Open and empty it. The contents
may be composted, if required. Clean the interior of
the suction attachment. Close the bag again and fit
it in place securely
CAUTION: The unit should be switched off before
operating the control lever to change suction over to
blowing.
2. Blo wing Function
If you want to make use of the blowing function of the
unit, make sure that the collection bag has been fitted
as appropriate. Plug the unit in. Put the carry strap
over your shoulder and adjust its length. Place the
control lever in the position marked „Gebläse" (fan).
Put the suction attachment in the working position in
front of you. Move forward slowly, collect the leaves
or blow it off any inaccessible places. While doing so,
use sweeping movements. Blowing may be used to
remove leaves from corners, fences, walls, tree
stands or from below the cars. Mind the air stream
direction as it can move even heavy objects able to cause
damage or injury. When the leaves are collected on a pile,
you may switch over to suction, pick them up and shred them.
3. Com posting
The garden vac has a crusher disc to work leaves and other
garden waste when the suction feature is employed.
Collected material is reduced at a ration of 10:1 while being
crushed. The quantity gets less and the material may be
composted. Make sure that the collected material is really fir
for composting.
Operator Safety Instructions
Do not use before reading the instruction
manual carefully.
Observe all the safety instructions contained in
the manual.
Be responsible to the others.
Step-by-Step Instructions
Fit the leaves collection bag.
Se the required function (suction/blowing) on the unit
Adjust the carrying strap for it to answer your needs.
Plug in the unit.
Start up the unit and select the required degree of output
.
Troubles - Causes – Troubleshooting
Trouble
Cause
1.
The unit will not run
2.
Inspections and Maintenance
Inspections and Maintenance
Before opening the cleaning hole or the protection
cover switch off and unplug the unit.
To provide for a maximum output any time and the unit safety, the
unit should be kept clean all the time. After the use, remove the
bag, open it and clean inside. .Keep the unit clean and .unblocked .
Clean the vents and the suction tube with a wet cloth and soft
brush.
Inspections and Maintenance Safety Instructions
The machine will serve as a sufficient aid only if maintained and
cared for appropriately. Insufficient maintenance and care may
result in accidents and injuries.
Inspections and Maintenance Schedule
Time interval
Description
After use
Clean the unit thoroughly and make sure that
the crushing disc is not damaged .
10
Troubleshooting
Defective
1.
Check the line.
2.
Check the line
cable
Defective
and the fuse.
socket

Publicité

loading

Ce manuel est également adapté pour:

Gls 2500 va9405294056