Folding down
- Loosen the fixation knob (7) halfway down the (LH) upright tube
while supporting the running deck, and remove it from the frame�
- Fold down the treadmill deck supporting it all the way down�
Avoid the power cable from being pinched while unfolding�
- Fit fixation knob on the bottom (LH) side of the trainer and fix it
firmly�
Refer to the illustrations for the correct way of unfolding and folding
the equipment�
Safety key (Fig F-3)
The equipment is equipped with a safety key that must be properly
inserted into the console to start the equipment� If you remove the
safety key from the console, the equipment will stop immediately�
- Insert the safety key into the slot in the console�
- Make sure that the clip of the safety key is properly attached to
your clothing�
Make sure that the clip is not removed from your clothing before
the safety key is removed from the console�
‼ NOTE
• Console will show "-- -- -- --" code when safety key is not in
(correct) position�
Console (fig. E-1)
⚠ CAUTION
• Keep the console away from direct sunlight�
• Dry the surface of the console when it is covered with drops of
sweat�
• Do not lean on the console�
• Only touch the display with the tip of your finger� Make sure that
your nails or sharp objects do not touch the display�
‼ NOTE
• The console switches to standby mode when the equipment is
not used for 10 minutes�
Buttons
Mode
- Select program mode (P0 ~ P12 )
- Confirm setting to enter next step in programming mode�
Set
- Set your target(s) for your workout when being in programming
mode�
Start/ stop
- Start selected workout after a 5 seconds countdown when being in
stop mode�
- When being in workout mode, trainer will come to a stop gradually�
Single arrow up (+ 0.1)
- Increases the speed with 0�1 km/h at the time�
- Pressing and holding for two seconds will increase the speed faster�
- Increase target values when being in programming mode�
Distance
+ 0�1 Km
Calories
+ 1�0 K/ Cal
Time
+ 1�0 min�
Dual arrow up (+ 1.0)
- Increases the speed with 1�0 km/h at the time�
- Pressing and holding for two seconds will increase the speed faster�
- Increase target values when being in programming mode�
- Increase target values when being in programming mode�
Distance
+ 1�0 Km
Calories
+ 10 K/ Cal
Time
+ 10 min�
Single arrow down (- 0.1)
- Decreases the speed with 0�1 km/h at the time�
- Pressing and holding for two seconds will decrease the speed
faster�
- Decreases target values when being in programming mode�
Distance
- 0�1 Km
Calories
- 1�0 K/ Cal
Time
- 1�0 min�
Dual arrow down (- 1.0)
- Decreases the speed with 1�0 km/h at the time�
- Pressing and holding for two seconds will decrease the speed
faster�
- Increase target values when being in programming mode�
Distance
- 1�0 Km
Calories
- 10 K/ Cal
Time
- 10 min�
‼ NOTE
• Speed control buttons are only functional in P0 workout mode�
Explanation of display items
Speed
- Show program selection when being in programming mode�
- Shows 5 seconds countdown when pressing "Start" button�
- Shows the actual treadmill speed in workout mode�
Display range:
1�0 ~ 10�0 Km/h ± 0�1 km/h
Time
- Shows the ran time in workout mode�
- Show remaining time when being in workout mode and have set a
workout target for time�
- Shows the target time when being in programming mode�
Display range:
00:01 ~ 99:99
Distance
- Shows the ran distance in workout mode�
- Show remaining distance when being in workout mode and have
set a workout target for distance
- Shows the target distance when being in programming mode�
- Display range:
0�0 ~ 99�9 Km ± 0�1 Km
Calories
- Shows the consumed calories in workout mode�
- Show remaining calories when being in workout mode and have set
a workout target for calories�
- Shows the target calories when being in programming mode�
- Display range:
0 ~ 999 K�Cal�
Calories indicator led burns when calories is shown�
‼ NOTE
• This data is a rough guide for comparison of different exercise
sessions which cannot be used in medical treatment
1 7
GB