STAMOS 6136 S-LS-18 Basic Manuel D'utilisation page 5

CAUTIONS
General safety information for the use of electrical devices:
To avoid injury from fire or electric shock, please ensure compliance with safety instructions when using
this device. Please read the instruction carefully and make sure that you have understood it well. Keep the
manual near the equipment to be able to read it at any time. Always use current sources connected to the
ground and providing the necessary voltage (indicated on the label on the device). If you have any doubt, let
an electrician check that your outlet is properly grounded. Never use a damaged power cable. Do not open
the unit in damp or wet environment, or if your hands or body are damp or wet. Protect the unit from
solar radiation. Use the device in a protected location to avoid damaging the equipment or endangering
others. Make sure the device is able to cool and avoid placing it too close to other devices that produce
heat. Before cleaning, disconnect it. Use a soft damp cloth for cleaning. Avoid using detergent and make sure
that no liquid enters the unit. No internal element of this device needs to be maintained by the user. An
opening of the device without our approval leads to a loss of warranty.
General safety information for the use of the device:
• The user manual should be kept close to the device and should always be accessible for the users.
Instruct your employees how to use the device properly.
• Make sure the hot air can circulate well and place the device more than 10 cm away from walls and
other electrical devices. Properly aerate the working area.
• Do not place the device close to combustible materials.
• When first using the device the heating element may produce a light smoke. This is absolutely normal.
Simply ensure that the smoke can evaporate and that a good aeration is provided.
• Some parts of the device can get extremely hot. To avoid any injuries, be careful whenever you come
into contact with the device.
• Clean the device regularly to avoid permanent accumulation of dirt.
TECHNICAL DETAILS
Model
Voltage (V)
Rated current (A)
Temperature range (⁰C)
Power (W)
Work temperature (⁰C)
Storage temperature (⁰C)
USAGE PURPOSE
The device is designed for:
Different kinds of soldering and de-soldering of the electronic components such as: SOIC, CHIP, QFP,
PLCC, BGA, SMD, etc.
Any damage resulting from a non-conform use of the device is to be paid by the user!
8
EN
6136 S-LS-18 Basic
230 ~ 50Hz
1
35-45-60
200-500
0 - 40
-20 / +80
PRINCIPLE OF OPERATION
Assembly:
BEFORE FIRST USE
Upon receipt of the goods, check the packaging for integrity and open it. If the packaging is damaged, please
contact your transport company and distributor within 3 days, and document the damages as detailed as
possible. Do not turn the package upside down! When transporting the package, please ensure that it is
kept horizontal and stable. Please keep all packaging materials (cardboard, plastic tapes and styrofoam), so
that in case of a problem, the device can be sent back to the service centre in accurate condition.
Disposing of packaging
The various items used for packaging (cardboard, plastic straps, polyurethane foam) should be conserved,
so that the device can be sent back to the service centre in the best condition in case of any problems!
INSTALLING THE APPLIANCE
Appliance location
The work surface where the device will be located must be suitable for the size of the appliance, please
refer to the measurements.
The work surface must be levelled, dry, heat-resistant and at a fitting height from the ground to enable a
proper use of the device.
The power cord connected with the appliance must be properly grounded and correspond to the technical
details.
OPERATION
1. Device must be placed on a stable work table, soldering iron must be placed into the holder.
2. Fix the appropriate soldering tip and connect the device to the power source.
3. Turn on the soldering iron with switch (1), power indicator (7) lights during working.
4. Set the desired temperature using knob (3): MIN=~200°C; MIDDLE=~330°C; MAX=~500°C.
5. After work, the soldering iron should be placed into the holder and turned off.
GENERAL REMARKS
1. When the device is being turned on, the soldering iron should be placed in the holder.
2. Good ventilation of the room in which the appliance is used must be provided. In addition, the device
should be placed in a location with good air circulation to dissipate heat.
SAFETY ISSUES REMARKS
1. Tips can be changed when the soldering iron is completely cold.
2.
EN DE
1. on / off switch
2. power cord
3. temperature adjustment knob (MIN=~200°C;
MIDDLE=~330°C; MAX=~500°C)
4. soldering iron cable
5. cleaning sponge
6. soldering iron steel holder
7. power indicator light
8. soldering iron
9