Technical Data; Before Starting The Equipment - EINHELL RG-EM 1538 Mode D'emploi

Anleitung_RG_EM_1538_SPK1:_

4. Technical data

Mains voltage:
Power input:
Motor speed:
Cutting width:
Cutting height adjustment:
Volume of catch bag:
L sound pressure level:
pA
L sound power level:
WA
Vibration at the handlebars:
K uncertainty
Protection class:
Keep the noise emissions and vibrations to a
minimum.
Only use appliances which are in perfect working
order.
Service and clean the appliance regularly.
Adapt your working style to suit the appliance.
Do not overload the appliance.
Have the appliance serviced whenever
necessary.
Switch the appliance off when it is not in use.
Wear protective gloves.

5. Before starting the equipment

The lawn mower is delivered unassembled. The
complete push bar and the grass basket must be
assembled before using the lawn mower. Follow the
operating instructions step-by-step and use the
pictures provided as a visual guide to easily
assemble the machine.
Mounting the push bar (Fig. 3 to 10)
Take the push bar brackets and insert them into the
two respective openings (Fig. 3). Attach the push bar
brackets as shown in Fig. 4, using the screws
provided.
The lower push bar then has to be slid onto the push
bar bracket (Fig. 5). Important. Do not forget to first
insert the stress-relief clip (Fig. 5/Item 1) onto the
lower push bar.
Screw the tubes together, using the screws supplied
(A), the plastic parts (B) and the hand wheel (C).
Now push the upper push bar over the lower push
bar (Fig. 7) and screw together as shown in Fig. 8.
Then attach the power cable to the push bar (Fig.
10/Item A) using the cable clips (Fig. 9).
16.12.2009 8:31 Uhr
Fitting the grass box
(see Figs. 11 and 12)
First, plug the right (Fig. 2/Item 15) and left (Fig.
230 V ~ 50Hz
2/Item 14) part of the housing together as shown in
1500 W
Figure 11a. Then plug the front part of the housing
(Fig. 2/Item 17) onto the already mounted parts (Fig.
3,400 rpm
11b). Finally, connect the top part of the housing (Fig.
38 cm
2/Item 16) to the bottom part of the box (Fig. 11c).
Before you fit the grass bag you must ensure that the
25-75 mm; 6 levels
motor is switched off and the blade is not rotating.
43 liters
Lift the ejector flap (Fig. 12 / Item A) with one hand.
73 dB(A)
With the other hand, hold the grass bag by the
handle and attach it from above (Fig. 12).
96 dB(A)
≤ 2.5 m/s
Adjusting the cutting height
1,5 m/s 2
Important. Adjust the cutting height only when the
motor is switched off and the power cable has been
II /
disconnected.
Before you begin to mow, check to ensure that the
blade is not blunt and that none of the fasteners are
damaged. To prevent any imbalance, replace blunt
and/or damaged blades. To carry out this check, first
switch off the motor and pull out the power plug.
The cutting height is adjusted as follows
(see Fig. 13):
To adjust the cutting height press the button (A)
and push down or raise the device. Once the
desired height has been set, button (A) must be
pulled up again.
Reading off the cutting height
The cutting height can be set between 25-75 mm in 6
intervals, and can be read off on the scale
(Fig. 13/B).
Power supply
The lawn mower can be connected to any light
socket-outlet with a 230 Volt alternating current.
However, the socket outlet must have an earthing
contact protected by a 16 A circuit breaker.
Additionally, a residual current device (RCD) circuit-
breaker with max. 30 mA must be used!
Power cable for the device
Please only use power cables that are not damaged.
The total length of the power cable should not
exceed 50 meters; going beyond this distance will
reduce the power output of the electric motor. The
power cable must have a cross-section of 3 x 1.5
mm 2 . The insulating sheath of lawn aerator power
cables is frequently damaged. Some of the causes
for this are:
Cuts caused by running over the cable
Seite 15
GB
15