Jump Start Warnings; Jumpstarting; Work Light - Wagan Tech Power Dome EX Guide D'utilisation

Masquer les pouces Voir aussi pour Power Dome EX:
Table des Matières

Publicité

Les langues disponibles

Les langues disponibles

Power Dome
EX by Wagan Tech
5. Remove the valve cap from the valve stem of the tire.
6. Attach the chuck to the tire's valve stem.
7. Move the chuck lever down to secure the chuck to the valve stem.
8. Turn compressor switch on to "I" position.
9. Monitor the pressure gauge while inflating the tire.
10. When recommended tire pressure has been reached, turn off air compressor.
11. Disconnect hose and replace valve cap.
12. Store the hose in the Air Hose Compartment.
13. Recharge the Power Dome as soon as convenient.

Jump Start Warnings

Lead-acid batteries can release explosive gasses. Failure to follow instructions
may cause property damage, explosion hazard, and/or personal injury.
Do not smoke while jump starting.
Jump start a vehicle or boat in a well ventilated area.
Do not attempt to jump start a frozen battery.
Do not wear vinyl clothing when jump starting—friction can cause static
electricity sparks.
Remove all metal jewelry—this can cause short circuits.
Always use safety glasses when jump starting battery—acid can cause
blindness and/or severe burns.
Never allow red and black clamps to touch—this can cause power arcing
and/or explosion.
After use, turn off Power Safety switch.
Keep out of reach of children.
Excessive engine cranking can damage the vehicle's starter motor. If the engine fails
to start after the recommended number of attempts, discontinue jump start procedure
and look for other problems that may need to be corrected.
If vehicle to be started has a Positive Grounded System (positive battery terminal is
connected to chassis):
i.
Connect negative (-) black clamp to vehicle battery's negative terminal.
ii. Connect positive (+) red clamp to vehicle chassis or a solid, non-moving,
metal vehicle component or body part. DO NOT clamp directly to positive
battery terminal or moving part.
www.wagan.com
7
User's Manual—Read before using this equipment

Jumpstarting

1. Review the Jump Start Warnings.
2. Make sure all vehicle appliances, lights, radio, etc are turned off.
3. Make sure the vehicle's gear is in "park" position and the brake is set.
4. Make sure all Power Dome switches are off.
5. Securely connect the red (+) cable clamp to the vehicle's positive (+) battery terminal.
6. Connect the black (-) cable clamp to a non-moving part on the vehicle.
7. Observe the color of the Reverse Polarity Protection Indicator that is located between
the Battery Status button and Work Light switch.
If the light is RED, DO NOT TURN ON THE JUMPER SAFETY SWITCH!
i.
Cable clamps need to be reversed.
ii. Disconnect the black clamp first then the red clamp.
iii. Reconnect and observe the indicator again.
If the light is GREEN, turn on the Jumper Safety Switch.
i.
Inside the vehicle, turn on the ignition switch and attempt to start the
engine.
ii. Crank a maximum of three seconds. If the engine does not start, wait
three minutes before the next attempt.
iii. After the engine starts, turn off the Jumper Safety Switch.
iv. Disconnect the black clamp first, and then disconnect the red clamp.
8. Be sure that the cables and clamps are securely stored.
9. Recharge the Power Dome as soon as convenient.
NOTE: If the engine does not start, there may be a problem other than a discharged battery.
Call for service.

Work Light

The Work Light is a cluster of bright LEDs located above the negative Jumper Cable storage
area. The location of the Work Light allows the light to be used while the Power Dome is being
carried.
Turn the work light switch (located on front panel) to the "I" position for power on.
The light will illuminate.
Turn off while not in use.
©2010 Wagan Corporation
Wagan and wagan.com are trademarks used by Wagan Corporation
All Rights Reserved
8

Publicité

Table des Matières
loading

Ce manuel est également adapté pour:

2454

Table des Matières