Information For Environmental Protection/ Disposal - IKRA IART 2520 LI Manuel D'utilisation

Attention: After assembly, the protection cover will
permanently remain mounted to the trimmer. The device
must never be operated without protection cover!
Install additional handle (Fig. 4 and 5)
Turn off the knob and remove the threaded bolt from the
included handle. Put the handle onto the tube as shown
in Fig. 4. Slide the handle to the desired position and fix
it using the threaded bolt and knob.
Cutting width indicator/plant protector guard (Fig. 6)
The bar on the front of the strimmer serves as a plant
protector guard and a cutting width indicator. The cutting
blade only moves within the dimensions of the unfolded
bar. However, the strimmer can also be operated with
the bar folded up if required.
Putting the machine in operation
• Insert the charged battery in the strimmer until the
interlock (15) latches. The rechargeable battery can
only be inserted in the strimmer in one position (Fig. 7).
Attention: When inserting the battery do not actuate
the switch-on inhibit (2) and the on/off switch (1).
• Adopt a safe stance. Hold the strimmer in both hands.
Do not set the cutting device down on the ground.
• Press the switch-on inhibit (2) to the left or right and
actuate the switch (1) (Fig. 8). After switching on, the
switch-on inhibit (2) must no longer be held.
• In order to switch off, release the switch (1) (Fig. 8).
Directions for set lenght adjustment and the
use of the set as edge cutter
The tube length may be adjusted to suit your height
(Fig. 9)
• To do so, turn the ribbed plastic sleeve clockwise to
loosen the connection. Adjust the tube to the suit-
able length and fasten the connection by turning the
tapped sleeve anti-clockwise.
Adjusting the tilting angle (Fig. 10):
• Press the button (8) - the strimmer head is disen-
gaged and can be pivoted in four positions relative
to the shaft.
Adjusting for edge trimming (Fig.10, 11 and 12):
• Set the tilting angle as previously described.
• Turn the handle (Fig. 11): Lift the plastic cover up-
wards to release (1). It is now possible to turn the
handle through 180° (2). The plastic cover must be
subsequently latched into place again.
Instructions for operating the mowing ma-
chine
(fig. 13)
• Move the mowing machine evenly from oneside to
another.
• If possible, mow by using the left half of the mowing
machine. The mowed parts of plants and / or stones will
thus be hurled forward away from the operating person.
• The best possible cutting result are achieved when
you hold the trimmer with an angle of 20°- 30° to the
left side.
• Avoid contact between the mowing string and obsta-
GB | Operating Instructions
(Fig. 7 and 8)
(Fig. 9,10,11,12)
GB-8
cles such as fences, walls, stones, etc. This leads to
excessive wear and tear.
Changing the plastic blade
Attention - risk of injury! Always remove the re-
chargeable battery from the device before all work.
Disassembling the plastic blade:
Push the blade off the retainer stud (1) towards the cen-
tre of the blade disc and remove (2).
Fitting the plastic blade:
Fit the blade over the retainer stud on the blade disc (1)
and pull outwards (2).
Maintenance and care
Attention - risk of injury! Always remove the re-
chargeable battery from the device before all work.
Clean your battery-operated mowing machine thor-
oughly each time after you use it. Remove the grass and
dirt. Clean the ventilation openings. It is best to clean the
plastic parts with a wet cloth and a soft detergent. Never
use aggressive detergents or solvents. Do not pour
water into the machine and do not sprinkle it with water.
Store the mowing machine in a dry place, never expose
it to frost and keep it out of children's reach.
For more extensive maintenance or repairs, give the
mowing machine to the service center.
Repair service
Repairs to electric power tools should only be carried out
by a specialised electrician.
Information for environmental protection/
disposal
Dispose of the machine properly after it is worn out. Dis-
connect the mains cable in order to prevent misuse. Do
not dispose of the machine with the household waste. In
the interest of environmental protection, take it to a col-
lection point for electric machines. Your responsible local
authority can provide you with addresses and operating
times. Also take the packaging materials and worn out
accessories to the appropriate collection points.
Only for EU countries
Do not discard electric tools in the house-
hold waste!
In accordance with European Directive 2012/19/EC on
waste electrical and electronic equipment and its im-
plementation in national law, waste electric tools must
be collected separately for environmentally-compatible
re-use.
Recycling alternative to the return invitation:
Instead of returning the electric equipment, the owner is
alternatively obligated to take part in the proper recycling
in the case of relinquishment of ownership. The waste
equipment can also be taken to a collection facility which
disposes of it in the sense of the national recycling man-
agement and waste acts. This does not pertain to the
accessory parts and auxiliary equipment without electri-
cal components accompanying the waste equipment.
(Fig. 14 and 15)