Ec Declaration Of Conformity - Flymo EasiCut 420 Instructions D'origine

If any part is found to be defective due to faulty manufacture the
guarantee period, Husqvarna UK Ltd., through its Authorised
Service Repairers will effect the repair or replacement to the
customer free of charge providing:
(a) The fault is reported directly to the Authorised Repairer.
(b) Proof of purchase is provided.
(c) The fault is not caused by misuse, neglect or faulty
adjustment by the user.
(d) The failure has not occurred through fair wear and tear.
(e) The machine has not been serviced or repaired,
taken apart or tampered with by any person not
authorised by Husqvarna UK Ltd..
(f) The machine has not been used for hire.
(g) The machine is owned by the original purchaser.
(h) The machine has not been used commercially.
* This guarantee is additional to, and in no way
diminishes the customers statutory rights.
Failures due to the following are not covered, therefore it
is important that you read the instructions contained in
this Operator's Manual and understand how to operate
and maintain your machine:
Husqvarna AB, 561 82 Huskvarna, Sweden
Declare under our sole responsibility that the product(s);
Category............................Electric HedgeTrimmer
Type(s) ..............................EC420, EC450, EC510, EC600
Identification of Series.......See Product Rating Label
Year of Construction..........See Product Rating Label
Conforms to the essential requirements & provisions of the following EC Directives:
98/37/EC (until 31.12.09), 2006/42/EC (from 01.01.10), 2004/108/EC, 2000/14/EC
based on the following EU harmonized standards applied:
EN60745-1, EN60745-2-15, EN774, EN50366, EN55014-1, EN61000-3-2, EN61000-3-3
The maximum A weighted sound pressure level L
the above product(s) corresponds to the Level given in the table.
The maximum hand / arm vibration weighted value measured according to EN ISO 5349 on a sample
of the above product(s) corresponds to the Value given in the table.
2000/14/EC: The Measured Sound Power L
the tabulated figures.
Conformity Assessment Procedure...............
Notified Body.................................................
Newton Aycliffe 19/10/2009
M.Bowden
Research & Development Director
Husqvarna UK Ltd.
Keeper of technical documentation
Type
Blade length (cm)
Power (kW)
Measured Sound Power L
Guaranteed Sound Power L
Level (dB(A))
Value (m/s )
2
Uncertainty K of a
Weight (Kg)
Guarantee and Guarantee Policy

EC DECLARATION OF CONFORMITY

WA
(dB(A))
WA
(dB(A))
WA
(m/s )
2
h
ENGLISH - 3
Failures not covered by guarantee
* Replacing Cutting Line.
* Failures as a result of not reporting an initial fault.
* Failures as a result of sudden impact.
* Failures as a result of not using the product in
accordance with the instructions and recommendations
contained in this Operator's Manual.
* Machines used for hire are not covered by this guarantee.
* The following items listed are considered as wearing
parts and their life is dependent on regular
maintenance and are, therefore not normally subject to
a valid warranty claim: Blades, Electric Mains cable,
* Caution!
Husqvarna UK Ltd. does not accept liability under the
warranty for defects caused in whole or part, directly or
indirectly by the fitting of replacement parts or
additional parts that are not either manufactured or
approved by Husqvarna UK Ltd., or by the machine
having been modified in any way
at the operator's position, recorded on a sample of
pA
& Guaranteed Sound Power L
Annex V
Intertek, Cleeve Road
Leatherhead, Surrey
KT22 7SB, England
EC420
42
0.42
97
99
86
5.56
1.5
2.8
values are according to
WA
EC450 EC510 EC600
45 51
0.45 0.50
97 99
105 106
86 88
5.53 2.23
1.5 1.5
2.8 2.9
60
0.50
96
97
85
3.30
1.5
3.0