Jotul F 350 Manuel D'installation Et Données Techniques page 10

ENGLISH
3.0 Installation
3.1 Floor
Foundations
It must be ensured that the foundations are dimensioned for
the fireplace. Cf. «2.0 Technical data» for specification of weight.
It is recommended that flooring which is not fastened to the
foundations – so-called floating flooring – is removed during
installation.
Combustible floor protection
If the fireplace is to be mounted on a combustible floor, cover
the floor under and in front of the fireplace with a plate made
of metal or other non-combustible material. The recommended
minimum thickness is 0.9 mm.
Any flooring made of combustible material, such as linoleum,
carpets, etc. must be removed from under the floor plate.
Requirement for protecting combustible
flooring in front of fireplace
The front plate must be in accordance with national laws and
regulations. Contact your local building authority regarding
restrictions and installation requirements.
3.2 Walls
Distance to wall made of combustible material
- see fig. 1.
You may use the fireplace with an uninsulated flue pipe provided
the distances to walls made of combustible materials are as
shown in fig. 1.
Distance to walls covered by a firewall
Contact your local building authority regarding restrictions and
installation requirements.
Firewall requirement
The firewall must be at least 100 mm thick and be made of
brick, concrete-stone or light concrete. Other materials and
constructions with satisfactory documentation may also be used.
Distance to non combustible walls
By non combustible one means a non load-bearing wall of
solid brickwork/concrete. Contact your local building authority
regarding restrictions and installation requirements.
3.3 Ceiling
There must be a minimum distance of 1000 mm to a combustible
ceiling above the fireplace.
3.4 Chimneys and flue pipes
• The fireplace can be connected to a chimney and flue
pipe approved for solid fuel fired appliances with flue gas
temperatures specified in «2.0 Technical data».
10
• The chimney's cross-section must be at least as big as the
flue pipe's cross-section. See «2.0 Technical data» when
calculating the correct chimney cross-section.
• Several solid fuel fired appliances can be connected to the
same chimney if the chimney's cross-section is sufficient.
• Connection to the chimney must be carried out in accordance
with the installation instructions from the supplier of the
chimney.
• Before making a hole in the chimney the fireplace should be
test-mounted in order to correctly mark the position of the
fireplace and the hole in the chimney. See fig. 1 for minimum
dimensions.
• Ensure that the flue pipe is inclined all the way up to the
chimney.
• Use a flue pipe bend with a sweeping hatch that allows it
to be swept.
Be aware of the fact that it is particularly important that
connections have a certain flexibility in order to prevent
movement in the installation leading to cracks. N.B. A correct and
sealed connection is very important for the proper functioning
of the product.
Chimney draught; See «2.0 Technical data». If the draught is
too strong you can install and operate a flue damper to control
the draught.
3.5 Assembly
N.B. Check that the fireplace is free of any damage prior to
commencing installation.
The product is heavy! Make sure you have assistance when
erecting and installing the fireplace.
The product is delivered in one package.
The stove, with a box containing a flue outlet with gasket and
screws, log retainer, heat shield, gasket and a tool to handle the
grate.
Mounting of rear flue pipe (see fig. 2).
• Unscrew the screw in the centre of the back heat shield (C).
Lift the plate up and out of the lower edge.
Remove the stamped part on the back of the heat shield (A)
•
by the aid of a hacksaw or cutters. Then fasten the flue outlet
from within with a gasket and the three M6 screws found in
the screw bag (B).
• Replace the heat shield and fasten the screw.
Warning! Remember to cover the hole for the flue outlet on the
top plate with the heat shield. Fasten the screws for this from
the inside (fig. 3).
Top flue outlet (see fig. 3)
1. Mount the flue outlet to the top.
2. Place the gasket cord around the bottom part of the flue pipe's
narrow end and lead this into the product flue outlet.
3. Attach the flue pipe.
Warning! Remember to cover the hole for the flue outlet on the
back plate with the heat shield. Fasten the screws for this from
the inside (fig. 3).