General Safety; General Outline; Technical Data - BFT LIBRA Instructions D'utilisation Et D'installation

ENGLISH
Thank you for buying this product, our company is sure that you will be more
than satisfied with its performance.
This product is supplied with an "Instruction Manual" which should be read
carefully as it provides important information about safety, installation, op-
eration and maintenance.
This product complies with recognised technical standards and safety regula-
tions. We declare that it is in conformity with the following European Directives:
89/336/EEC, 73/23/EEC, 98/37/EEC and subsequent amendments.

1) GENERAL SAFETY

WARNING! An incorrect installation or improper use of the product can
cause damage to persons, animals or things.
WARNING! Installation must be carried out using the safety devices
and controls prescribed by the EN 12978 Standard.
The "Warnings" leaflet and "Instruction booklet" supplied with this
•
product should be read carefully as they provide important information
about safety, installation, use and maintenance.
• Scrap packing materials (plastic, cardboard, polystyrene etc) according
to the provisions set out by current standards. Keep nylon or polystyrene
bags out of children's reach.
• Keep the instructions together with the technical brochure for future
reference.
• This product was exclusively designed and manufactured for the use
specified in the present documentation. Any other use not specified in
this documentation could damage the product and be dangerous.
• The Company declines all responsibility for any consequences result-
ing from improper use of the product, or use which is different from that
expected and specified in the present documentation.
• Do not install the product in explosive atmosphere.
• The construction components of this product must comply with the following
European Directives: 89/336/CEE, 73/23/EEC, 98/37/EEC and subse-
quent amendments. As for all non-EEC countries, the above-mentioned
standards as well as the current national standards should be respected
in order to achieve a good safety level.
• The Company declines all responsibility for any consequences resulting
from failure to observe Good Technical Practice when constructing clos-
ing structures (door, gates etc.), as well as from any deformation which
might occur during use.
• The installation must comply with the provisions set out by the following
European Directives:89/336/CEE, 73/23/EEC, 98/37/EEC and subsequent
amendments.
• Disconnect the electrical power supply before carrying out any work on
the installation. Also disconnect any buffer batteries, if fitted.
• Fit an omnipolar or magnetothermal switch on the mains power supply,
having a contact opening distance equal to or greater than 3,5 mm.
• Check that a differential switch with a 0.03A threshold is fitted just before
the power supply mains.
• Check that earthing is carried out correctly: connect all metal parts for
closure (doors, gates etc.) and all system components provided with an
earth terminal.
• Fit all the safety devices (photocells, electric edges etc.) which are needed
to protect the area from any danger caused by squashing, conveying and
shearing.
• Position at least one luminous signal indication device (blinker) where it
can be easily seen, and fix a Warning sign to the structure.
• The Company declines all responsibility with respect to the automation
safety and correct operation when other manufacturers' components are
used.
• Only use original parts for any maintenance or repair operation.
• Do not modify the automation components, unless explicitly authorised
by the company.
• Instruct the product user about the control systems provided and the
manual opening operation in case of emergency.
• Do not allow persons or children to remain in the automation opera-
tion area.
• Keep radio control or other control devices out of children's reach, in
order to avoid unintentional automation activation.
• The user must avoid any attempt to carry out work or repair on the automa-
tion system, and always request the assistance of qualified personnel.
• Anything which is not expressly provided for in the present instructions,
is not allowed.
• Installation must be carried out using the safety devices and controls
prescribed by the EN 12978 Standard.

2) GENERAL OUTLINE

The LIBRA-MA-R control panel is supplied by the manufacturer with standard
setting. Any alteration must be set by means of the incorporated display
programmer or by means of UNIPRO. The Control unit completely supports
the EELINK protocol.
12 - LIBRA-MA-R - Ver. 05
INSTALLATION MANUAL
Its main characteristics are:
- Control of two low-voltage motors up to 40W power
- Electronic torque setting with obstacle detection
- Limit-switch control inputs
- Separate inputs for safety devices
- Incorporated rolling-code radio receiver with transmitter cloning
The board is provided with a terminal board which can be pulled out for
easier maintenance or replacement. The board is supplied with a series of
pre-wired jumpers to facilitate the installer's work.
The jumpers relate to the following terminals: 15-17 and 15-18. If the above-
mentioned terminals are in use, remove their respective jumpers.
CHECK
The LIBRA MA-R panel carries out a control (check) on the starting relays
and safety devices (photocells, safety edge etc.) before carrying out each
opening and closing cycle.
In case of malfunction, check the devices connected for regular operation
(paragraph 5.6) and check the wiring.

3) TECHNICAL DATA

Power supply: ...........................................................230Va.c. ±10% 50Hz*
Mains/low voltage insulation: ......................................... > 2MOhm 500Vdc
Working temperature: ............................................................. -10 to +55°C
Dielectric strength:.... ................. mains/low voltage 3750Vac per 1 minute
Motor output current: ..........................................................3.5A+3.5A max
Motor relay commutation current: ......................................................... 10A
Maximum motor power: ........................................................ 40W (24Vd.c.)
Supply to accessories: ............................ 24Va.c. (180mA max absorption)
Gate-open warning light: ............................ N.O. contact (24Va.c./1A max)
Blinker: ............................................................................ 24Va.c. 25W max
Dimensions: ..............................................................................see figure 1
Fuses: .......................................................................................see figure 2
(* other voltages available on request)
BATTERY KIT BT BAT (Fig.6)
Charging voltage:............................................................................ 27.2Vdc
Charging current:.............................................................................. 130mA
Outside temperature when values were measured: ............................ 25°C
Battery capacity:.................................................................. 2x (12V 1.2Ah)
Flat battery protection threshold:.................................................. 20.4Vd.c.
Battery charging time:................................................................... 12/14 hrs
NOTE: In case of operation with battery back up, the outputs to terminals
11-12 (24 Va.c.) and 13-14 ( Vsafe 24 Va.c.) have a voltage of 24 Vd.c.,
polarised as shown in Fig. 6.
When installing the BT-BAT kit, check for correct connection of the safety
devices.
4) TERMINAL BOARD CONNECTIONS (Fig.3)
WARNING – During the wiring and installation operations, refer to the current
standards as well as principles of good technical practice.
Wires powered at different voltages must be physically separated, or suitably
insulated with at least 1 mm extra insulation. The wires must be clamped by
an extra fastener near the terminals, for example by bands.
All the connection cables must be kept at an adequate distance from the
dissipator.
WARNING! For connection to the mains, use a multipolar cable with
a minimum of 3x1.5mm
ously mentioned regulations. For example, if the cable is out side (in
the open), it has to be at least equal to H07RN-F, but if it is on the inside
(or outside but placed in a plastic cable cannel) it has to be or at least
egual to H05VV-F with section 3x1.5mm
JP1
1-2 Single-phase mains power supply 230Va.c. ±10% (1=L) (2=N)
JP9
3-4-5 Connection to motor 2:
3 motor + (red)
4 motor - (black),
5 limit-switch control (white)
6-7-8 Connection to motor 1:
6 motor + (red)
7 motor - (black)
8 limit-switch control (white)
9-10 Connection to blinker (24Va.c. 20W max)
24Va.c. V safe (180mA max absorption)
2
cross section and complying with the previ-
2
.