Silverline 946680 Traduction Des Instructions Originales page 7

946680
WARNING: Only use this Charger to charge the supplied Battery.
WARNING: The Battery Charger is designed for indoor use only and must not be exposed
to moisture and rain.
Charging the battery
WARNING: Failure to follow the correct procedure when charging the batteries will result
in permanent damage.
Note: Normal charging time is 3-5 hours for a recently fully-discharged battery, but if
the Battery has been left in a discharged state for some time, it may take extended time
to charge.
1. Slide a discharged or partially discharged Battery into the Battery Charger (17)
2. Both the Green LED (19) and Red LED (20) will flash to show the Battery is being
assessed by the charger
3. Once charging commences, both LEDs will illuminate without flashing
4. When the Battery is fully charged only the Green LED will be illuminated
Note: If both LEDs are not constantly illuminated after the charger has assessed the
Battery (11), this indicates a fault condition. Recheck the Battery is fully inserted in the
Battery Charger and connecting with the Battery Contacts (18). Remove any material that
may have fallen into the battery socket of the Battery Charger and make sure the contacts
of both the Battery and the Battery Charger Unit are clean, untarnished metal and not
damaged or bent.
Notes about battery charging:
• The Battery (11) should be charged at ambient temperatures between 10 and 40°C
(ideally around 20°C)
• After charging, allow 15 minutes for the battery to cool before use
• Ensure that the charger is disconnected from the mains supply after use, and is stored
correctly
• DO NOT leave batteries on charge for extended periods and NEVER store batteries on
charge
• The Battery Charger (17) monitors battery temperature and voltage while charging.
Remove the Battery once charging has been completed to maximise charge cycles of
the battery and not waste power
• Batteries can become faulty over time, individual cells in the battery can fail, and the
battery could short. The charger will not charge faulty batteries. Use another battery,
if possible, to check correct functionality of the charger and purchase a replacement
battery if a faulty battery is indicated
• DO NOT store Lithium-ion battery packs in a discharged state long term. This can
damage the Lithium-ion cells. For long-term storage, store batteries in a high charge
state disconnected from the power tool
• The capacity of batteries will reduce over time. After 100 charge cycles, the battery's
operation time and the maximum torque performance of the drill will slightly reduce.
This decline will continue until the battery has minimal capacity after 500 charge cycles.
This is normal and not a fault with the battery pack
Fitting drill bits and accessories
WARNING: Always remove the Battery from the drill before attaching, adjusting or
removing accessories.
WARNING: Do not attempt to tighten drill bits (or any other accessory) by gripping the
Chuck Collar (2) and switching the tool on. This can lead to personal injury and can cause
damage to the chuck.
WARNING: Never fit any attachment with a maximum speed lower than the no-load speed
of the power tool or selected gear.
1. Open the Chuck Jaws (1) by rotating the Chuck Collar (2) anti-clockwise (with the chuck
facing the operator)
2. Place the drill bit or accessory into the Chuck Jaws correctly centralised
3. Tighten the Chuck Jaws by rotating the Chuck Collar clockwise
4. When the drill bit or accessory is securely fastened, carefully run the machine to test
that it is running centrally, smoothly and evenly. If the bit is 'wobbling' or not running
centrally, release the Chuck Jaws, check the accessory for damage, correct its position,
retighten and test again
Operation
Direction control
WARNING: NEVER change the direction of rotation while the tool is running.
• The direction of rotation can be set using the Forward/Reverse Switch (8)
• For anti-clockwise rotation, holding the drill in a normal operating position, push the
switch to the right
• For clockwise rotation, push the switch to the left
Note: When the Forward/Reverse Switch is in the central position, the drill is locked and
cannot be switched on. Use this setting as a safety feature to prevent the drill from being
switched on accidentally.
18V Combi Hammer Drill
Speed control
• This drill features a 2-speed gearbox:
- 1st gear range: 0 – 400/min
- 2nd gear range: 0 – 1450/min
• Use the Gear Selector (6) to set the gear: back for first gear, forward for second gear
Note: The first gear would be used normally for driving screws, for example, and offers
higher torque and superior control at low rpm. The second gear would normally be used
exclusively for drilling.
Drill mode selection
• For normal drilling, select the correct gear which is normally the high speed 2nd gear,
then rotate the Mode Selector (5) so the drill symbol
the tool body
• For masonry drilling, select the correct gear which is normally the high speed 2nd gear,
then rotate the Mode Selector so the hammer symbol
on the tool body
Torque control
• This drill driver is fitted with torque control, which limits the torque output of the drill,
enabling screws to be driven without the risk of damage
• There are 16 torque settings and two drill settings. The lower the number, the lower the
torque
• To set the torque clutch, select the first gear and rotate the Mode Selector (5) so the
drive symbol is aligned with the indicator on the tool body
• Rotate the Torque Selector (4) until the setting you require is aligned with the drive
symbol
• Check that the torque setting is correct by practising first on a piece of scrap material
WARNING: The drill can be fitted with a drive adaptor for use with driving nuts and bolts.
Do not attempt to use this tool in the drill position when doing so. Use the 16 torque
settings and the first gear to allow the torque clutch to protect the tool from excessive
load. The use of a spanner to loosen or tighten a nut/bolt is recommended. This allows the
tool to speed up the operation without risk of damage when high torque is required at the
beginning or end of the operation.
Switching on/off
WARNING: Always wear adequate personal protection equipment when setting up and
operating this machine.
1. To start the drill, squeeze the Trigger Switch (13)
Note: If the Trigger Switch cannot be pressed down, check that the Forward/Reverse
Switch (8) is not set to its middle position, which locks the device (see "Direction control").
2. The speed of the drill is controlled by the movement of the trigger: the further the trigger
is pressed down, the faster the drill will run
3. Release the Trigger Switch to stop the machine
Note: A built-in LED Work Light (14) will operate each time the Trigger Switch is pressed to
illuminate the work area.
Screwdriver use
Note: Use a universal bit holder (not supplied) when working with screwdriver bits. Only
mount screwdriver bits directly into the chuck if it is essential to access a screw head. Use
a bit holder at all other times.
• When driving screws NEVER use the machine in drill mode. This will protect the motor
by causing the clutch to slip rather than the motor to stall when the screw is fully
inserted in the workpiece and cannot rotate any further
• Always adjust the drill to the appropriate torque setting (see 'Drill mode selection' &
'Torque control')
Note: If in doubt about which torque setting best suits the application, start with a low
setting and increase, should more torque be required (e.g. if the screw is not being driven
far enough into the workpiece).
Drilling wood
WARNING: The dust produced from working with some materials can be toxic.
Beech, oak, mahogany and teak natural woods, man-made composite woods and some
surface treatments, including paint with lead, are toxic. Lead-based paint is common in
buildings built before 1960. Always wear suitable respiratory protection; for example, a
respirator face mask. Use a dust extraction system or regularly vacuum the work area to
prevent the build-up of dust. In addition, vacuum the work area after the work has been
completed. Most dust is a fire hazard. Overhead work surfaces have an increased safety
risk for dust.
• Select drill mode with the Mode Selector (5) and the required gear (typically 2nd
gear)
• Ensure that drill bits are suitable for wood, and are within the maximum capacity of this
power tool (see 'Specification')
www.silverlinetools.com
is aligned with the indicator on
is aligned with the indicator
7