Making Coffee; Cleaning And Maintenance - Melitta LOOK Selection DeLuxe Mode D'emploi

Hardness setting
°dH
Flash rhythm
CALC button 
Table 1
Warming time setting
Flash rhythm
START button 
Table 2
factory settings the CALC button flashes briefly four
times with the following pauses ............
• You can set the water hardness at three further
levels. Each time you briefly press the CALC button
 the display changes to flashing one, two or three
times, each time followed by a pause
(......, ......, ......).
• The settings and display are shown in the following
table 1.
• Once you have set the desired hardness level, again
hold the CALC button  down for longer than two
seconds. The light goes off and your settings are
saved.
Please note:
1. Water hardness cannot be programmed while
brewing.
2. The last water hardness level chosen remains even
after removing the power cable.
4. Setting the hotplate
Keeping coffee warm on the hotplate affects the taste
of your coffee. To avoid this you should enjoy your
coffee fresh by drinking it as soon after brewing as
possible. Unnecessary warming also uses valuable
energy. The factory settings for the appliance are for
40 minutes of warming. After this the hotplate turns
off automatically. This time can be changed as needed:
• Press the START button  longer than two seconds.
• In the factory settings the START button  flashes
briefly twice with the following pause (......).
• There are two other settings for the warming time.
By briefly pressing the START button  the display
changes to flashing three times or once, each time
followed by a pause (......, ......, ......).
• The settings and display are shown in table 2.
• Once you have set the desired warming time,
confirm your settings by pressing the START button
 for longer than two seconds. Your settings are
now saved
• The last setting chosen remains even after removing
the power cable.
1
2
<7°
7-14° dH
dH
............ ............
20 minutes
40 minutes
............ ............
3
14-21°
dH
............
60 minutes
............

5. Making coffee

• Ensure that the appliance is connected to the power
source.
• Open the lid on the water tank. 
• Fill the water tank with the desired amount of water
using the glass pot. With the help of the water level
display on the tank  you can choose the correct
number of cups. Small cup symbol = approx. 85ml
coffee per cup, large cup symbol = approx. 125 ml
coffee per cup.
• Close the lid on the water tank and place the glass
pot with closed lid in the appliance.
• Open the swivel filter  to the left.
filter bag 1x4
• Fold a Melitta
®
and place it in the filter holder.  Press the filter bag
into the filter holder by hand, to ensure a good fit.
• Put the ground coffee into the filter. The amount
depends on your personal taste. We recommend
using 6g of ground coffee per large cup.
• Swivel the filter back into the appliance. An audible
click tells you it is inserted properly.
Aroma Selector  you can
• With the Melitta
®
set the taste of your coffee with just one hand:
From mild-aromatic ( ) to strong-intensive (
• Turn the appliance on . Brewing begins.
• After making your coffee the hotplate will keep it
warm and will turn off automatically after the time
you have set (see point 4). This avoids unnecessary
use of electricity and saves energy. You can of course
turn the machine off manually at any time.
• The drip stop prevents your coffee from dripping,
when you remove the pot from the appliance. 
• With the help of the detachable inner filter you can
dispose of the filter bag simply and easily.

6. Cleaning and maintenance

External cleaning
• The housing can be cleaned with a soft damp cloth.
• The glass pot and lid, the filter insert and the swivel
filter  can be washed in the dishwasher.
• When cold, the hotplate can be cleaned with a soft
damp cloth.
GB
4
>21°
dH
............
at the embossed seam
®
).
9