Publicité
English
the screened cover. 9. Then, re-insert the filter cartridges in the following sequence into the filter container (9):
In professionel 4+ - 250 (Typ 2271) and 250 T (Typ 2371): 1. Filter cartridge with EHEIM MECH pro. 2. Filter
cartridge with EHEIM SUBSTRAT pro, white filter fleece and screened cover.
In professionel 4+ - 350 (Typ 2273), 350 T (Typ 2373) and professionel 5e - 350 (Typ 2274): 1. Filter cartridge
with EHEIM MECH pro. 2. Filter cartridge with EHEIM bioMECH. 3. Filter cartridge with EHEIM SUBSTRAT pro,
white filter fleece and screened cover.
In professionel 4+ - 600 (Typ 2275): 1. Filter cartridge with EHEIM MECH pro. 2. Filter cartridge with EHEIM MECH
pro. 3. Filter cartridge with EHEIM bioMECH. 4. Filter cartridge with EHEIM SUBSTRAT pro, white filter fleece
and screened cover.
10. Insert the prefilter (4) with the blue filter mat (1) (place onto supports fi arrows). 11. Attach the pump head
(17) (observe fitting position) and close the locking clips (8).
Note: Use original EHEIM hoses only.
12. Attach the pre-assembled hose accessories (see II) to the aquarium. 13. Cut hoses (23) to the desired length and attach
to the fittings. 14. Plug the hoses (24) onto the safety adapter (13) down to the limit stop. 15. Attach the hose locking
device (11). 16. Push the safety adapter (13) into the pump head (17) until it audibly latches. 17. Set the locking lever (12
to „ON". 18. Assure the the nozzle pipe (26) is suspended above the water surface. 19. Rapidly press the suction aid (16)
several times consecutively until the filter tank (10) automatically fills with water (no water must be present in the prefilter!).
20. Plug in the power supply unit (30) at the pump head (17) (only in professionel 5e - 350 Type 2274). 21. Plug in the
power cable (31) of the filter Caution: Operate the heater only (by plugging in the heater power cable) when the water starts
circulating and the filter supplies water 22. To vent the priming aid (16) press again 1 or 2 times and push the nozzle tube
(26) into the desired position.
6.
Operation (only on professional 5e 350, Type 2274)
System Requirements
WLAN-capable end device (smartphone, tablet, notebook etc.)
6.1
Creating a Network
Put the exterior filter into operation by plugging in the mains plug. The status LED of the pump head lights up:
• White flashing LED: Network is being sought or created.
• Blue LED: The controller has created a new network.
6.2
Connecting to the WLAN network #EHEIM Filter_XXXXXXXX
Open the network settings of the end device, for example, notebook, tablet or smartphone, and connect to the
WLAN network, #EHEIM Filter_XXXXXXXX..
6.3
Calling up the website
Open the internet browser and call up the web address http://eheimdigital.local or http://192.168.1.1.
6.4
Start the Configuration
Select the desired language in the language selection field and proceed with the initial configuration. Follow the
instructions accordingly. Detailed instructions can be downloaded via QR code on the title page or under
www.eheim.com.
7.
Thermofilter professionel 4+ - 250 T (Typ 2371) / 350 T (Typ 2373),
Only thermofilter: 33. Control indicator („ON" / „OFF") 34. LED indicator in Celsius (°C) 35. Status indicator for
target temperature in Celsius (°C) 36. Pushbutton 37. Display in Fahrenheit (°F) 38. Heating spiral.
Setting range of the target temperature
Factory setting of the target temperature
18° – 34°C
24°C / 75°F
23
see III
64° – 93°F
Publicité
