Table des Matières
Publicité
Les langues disponibles
Les langues disponibles
10. MAINTENANCE AND CARE
Check the external air intake, by cleaning it, at least once a year.
The stack must be regularly swept by the chimney sweeper.
Let your chimney sweeper in charge of your area check the regular installation of the device, the connection to the stack and the aeration.
IMPORTANT: The maintenance must be carried out only and exclusively with cold device .You should only use spare parts approved
and supplied by La NORDICA. Please contact your specialized retailer if you require spare parts. YOU MUST NOT MAKE ANY
CHANGES TO THE DEVICE!!!
10.1. GLASS CLEANING
After having checked that the door is completely shut (lowered), unlock the upper latch
clean the glass, then close the flap and lock the latch before lifting again the door.
Thanks to a specific inlet of secondary air, the accumulation of dirty sediments on the glass-door is reduced with efficacy. Nevertheless this
can never be avoided by using solid fuels ( particularly wet wood ) and it has not to be understood as a defect of the appliance.
IMPORTANT: The cleaning of the sight glass must be carried out only and exclusively with cold device to avoid the explosion of
the same. For the cleaning, it is possible to use specific products or a wet newspaper paper ball passed in the ash to rub it. Do not
use cloths, abrasive or chemically aggressive products by cleaning the hearth glass.
The correct lighting phase, the use of proper quantities and types of fuels, the correct position of the secondary air regulator, enough
draught of the chimney-flue and the presence of combustion air are the essential elements for the optimal functioning of the appliance and
for the cleaning of the glass.
BREAK OF GLASSES: Given that the glass-ceramic glasses resist up to a heat shock of 750°C, they are not subject to thermal
shocks. Their break can be caused only by mechanic shocks (bumps or violent closure of the door, etc.). Therefore, their
replacement is not included in the warranty.
10.2. CLEANING OUT THE ASHES
All the devices are equipped with a hearth grating and an ash drawer for the collection of the ashes.
It is suggested to empty periodically the ash drawer and to avoid it fills completely in order not to overheat the grating. Moreover, it is
suggested to leave always 3-4 cm of ash in the hearth.
CAUTION: The ashes removed from the hearth have to be stored in a container made of fire-resistant material equipped with an
air-tight cover. The container has to be placed on a fire-resistant floor, far from flammable materials up to the switching off
and complete cooling.
10.3. CLEANING THE FLUE
The correct lighting phase, the use of proper quantities and types of fuels, the correct position of the secondary air regulator, enough
draught of the chimney-flue and the presence of combustion air are the essential elements for the optimal functioning of the appliance.
The device should be completely cleaned at least once a year or every time it isaaa needed (in case of bad working and low yield). An
excessive deposit of soot can cause problems in the discharge of smokes and fire in the flue.
The cleaning must be carried out exclusively with cold equipment. This operation should be carried out by a chimney sweeper who
can simultaneously perform an audit of the flue (checking of possible deposits).
Excessive incrustation deposits on the inner walls of the hearth considerably reduce the efficiency of heat exchange; therefore, remove
these deposits using a steel brush whenever necessary. Never use corrosive substances that can damage the thermo-fireplace and
the boiler.
10.4. CLEANING THE FIREPLACE
During cleaning remove the top cap of the fireplace which is located on the exhaust fumes pos. B
the help of a hammer as indicated in to the picture) and the top lock steel plate of the fireplace pos. E by turning and pulling it down.
ATTENTION: when you remove the cap and the top lock steel plate of the fireplace, the dirtiness that is inside the chamber of exhaust
fumes falls down, therefore avoid to dirty the inside of the fireplace.
When the cleaning is completed: - put the top cap of the fireplace into its place (B). You have to support the cap to the wall above the
fireplace by passing it through the corresponding slots (C) and then, with a rotary movement of the hand, send the screws at the machined
seats into the wall (D) and leave the cap as support on the upper wall; - put into its place the top lock steel plate of the fireplace as indicated
in
Picture 11 at page 58
pos. E.
ATTENTION: The absence of the cap (B) and the top lock steel plate of the fireplace (E) causes a strong depression, leading to
excessively fast combustion and excessive wood consumption, with consequent overheating of the appliance, forge effect,
and decreases the heat discharge of the boiler.
10.5. MAINTENANCE ON THE WATER SYSTEM
Excessive incrustation deposits on the inner walls of the hearth considerably reduce the efficiency of heat exchange; therefore, remove
these deposits using a steel brush whenever necessary. Never use corrosive substances that can damage the thermo-fireplace and
the boiler.
With the system switched off, once a year carry out the following checks:
•
Check the operation and efficiency of the blowdown and safety valves. If they are defective, contact your authorised installer. IT IS
STRICTLY FORBIDDEN TO REMOVE OR TAMPER WITH THE SAFETY DEVICES.
•
Check the thermal insulation of the filling pipe and the safety pipe.
•
Make sure that the system is filled and under pressure, checking the water level in the expansion tank; also check that it is working
properly and check the efficiency of the safety pipe.
26
TERMOCAMINO BASE - DSA
(Picture 10 at page 58
pos. A), open the flap and
Picture 11 at page 58
6095011 - IT-EN-DE-FR
(the first time by
Publicité
Table des Matières
