General Warnings - AERMEC FCX P Manuel D'utilisation Et D'installation

IT EN FR

GENERAL WARNINGS

• WARNINGS REGARDING
STANDARDS
• Follow the indications below to install the equipment correctly.
The completion of all operations, according to specific
requirements, is left to the experience of the installer.
• Do not modify or tamper with the units, as dangerous situations
can occur. The manufacturer will not be liable for any damage
caused. The validity of the warranty shall be void in the event of
failure to comply with the indications mentioned in this manual.
• Before starting any operations, READ THESE INSTRUCTIONS
CAREFULLY AND CARRY OUT THE SAFETY CHECKS TO AVOID ALL
RISKS.
• All the staff involved must have thorough knowledge of the
operations and any danger that may arise when the installation
operations are carried out.
• The unit must be installed to facilitate routine (filter cleaning) and
special maintenance operations.
• ATTENTION: the fan coil is connected to the power supply
and the hydraulic circuit. Operations performed by persons who
do not have the required technical skills can lead to personal
injury to the operator or damage the unit and the surrounding
environment.
• ATTENTION: The unit must be installed in compliance with
national regulations.
• ATTENTION: make sure that the power supply has been
disconnected before carrying out any interventions.
• ATTENTION: Install a device, master switch or electric plug that
allows the unit's power supply to be completely disconnected.
• ATTENTION: In order to protect the unit against short circuits,
mount a magnet circuit breaker omnipolar switch on the power
supply line. In order to avoid any danger due to the accidental
rearming of the thermal cut-out device, this appliance must
not be powered with an external switching device, such as a
timer, or be connected to a circuit that is regularly powered or
disconnected from the service.
• ATTENTION! DANGER! Any use other than what is indicated
by Aermec is prohibited.
• Supply the fan coil only with the voltage value indicated in
the data plate
• The fan coil may be permanently damaged if a different electric
power supply is used.
• OPERATION ANOMALIES
• In the event of operation anomalies, power off the unit and then
power it back on and re-start the unit.
• Do not try to repair the unit on your own, as it may be very
dangerous!
• If the problem persists, call the Area After-sales Service
immediately.
• Do not pull the electric cable
• It is very dangerous to pull, step on or crush the power supply
cable or secure it using nails or staples.
• The damaged cable can cause short circuits and injury to persons.
• Electric power supply cable
• If the power supply cable is damaged, it must be replaced with
a new cable of adequate section. Have the repair made by
"Qualified personnel", in order to prevent any risk.
• Do not repair damaged cables.
• For the electric power supply, use integral cables with suitable
section for the load.
• Do not introduce objects into air vents
• Do not introduce any objects into the air outlet slots.
• This could cause injury to persons or damage the fan.
•
INFORMATION
10
DE ES
SAFETY AND INSTALLATION
•
• The FCX AERMEC units are constructed according to the
recognised technical standards and safety regulations. They
have been designed and must be used for air conditioning and
heating purposes, in accordance with their technical features.
• Any contractual or extra-contractual liability of the Company is
excluded for injury/damage to persons, animals or objects owing
to installation, regulation and maintenance errors or improper
use. All uses not expressly indicated in this manual are prohibited.
• Use suitable Personal Protective Equipment (PPE) during
installation, maintenance, and cleaning stages.
• Do not use the unit as storage for equipment or spare parts. Any
use other than that indicated in this manual is prohibited as it can
generate dangerous situations.
• ATTENTION: the electric and hydraulic connections, together
with installation of the fan coils and their accessories must
only be performed by technicians who have the technical-
professional requisites for installation, transformation, extension
and maintenance of the systems and who can verify these
functions in terms of safety and functionality (in accordance with
the national laws in force in the country of installation). In this
manual they will be also identified as: experienced and qualified
technician with specific technical knowledge.
• Aermec will not be liable for damage due to failure to follow these
instructions.
• Make sure the unit has not been damaged during transport
before installation.
• using a damaged machine could be dangerous.
• the support surface must withstand the weight of the unit.
• Note:
• Always indicate the serial number for future reference
and for any communication with AERMEC S.p.A.
• STORING THE DOCUMENTATION
• Hand over the instructions with all the related documenta-
tion to the system user, who must store the instructions so
that they are always available in case of necessity.
TRANSPORT
• Refer to the weight indications on the data plate to transport the
unit safely.
• Take the following measures during transport:
• The unit and the accessories must not undergo violent impacts in
order not to affect the integrity of the structure and of the internal
components;
• during transportation, the unit and any accessories must be
protected in order to prevent impacts, for this reason they must
be properly secured on the transportation floor with ropes or any
other means that prevent their movement;
• during transport and storage, the unit and the accessories must
always be protected against bad weather.
VERIFICATIONS UPON RECEPTION
• Visually check the unit upon reception to make sure that:
• the order corresponds with what is indicated in the transport
documents;
• packaging is intact;
• the unit is intact;
• all the components have been provided.
• Indicate any damage or missing components on the transport
document.
HANDLING
• ATTENTION! : Wear proper personal protective equipment (PPE)
during handling operations.
• Fully remove the unit and the components from the packaging
before installation and use.
FCX P_PO_PV 1605- 6456063_02