Lighting; Low Emission Fire Lighting - LA NORDICA TERMOCAMINO-650 Manuel Utilisateur

LIgHTINg

ATTENTION: never light for any reason if the installation is not completely full of water in order to avoid a serious damage
of the whole structure. IABsOLUTELY DO NOT LIgHT THE FIRE IN THE THERMO-FIREPLACE IN THE TOTAL OR PARTIAL
ABsENCE OF WATER (noT eVen foR CHeCkinG), as iT CoULd Be iRReMediaBLy RUined. in sUCH Case THe WaRRanTy on THe
appLianCe is Voided.
Before installing the facing and lighting the thermo-fireplace, it must be loaded and the system filled from the open expansion tank by means
of the natural fall of the water (see chapter. sysTeM ConneCTion and fiLLinG).
after ensuring that at least one radiator is always open, open the door and load a small quantity of wood.
To light the fire, it is suggested to use small wood pieces together with paper or other traded lighting means.
It is FORBIDDEN to use any liquid substance as for ex. alcohol, gasoline, oil and similar. Never switch on the device when
there are combustible gases in the room.
The openings for air (primary and secondary) must be opened together (you must open the eventual ignition control, and butterfly valve
placed on the pipe of smokes exhaust). When the wood starts burning, you may load other fuels and adjust the air for combustion according
to the instructions on paragraph TeCHniCaL desCRipTion.
Please always be present during this phase. Never overload the appliance (see cap. TeCHniCaL desCRipTion - Hourly
consumption). Too much fuel and too much air for combustion can cause overheating and therefore damage the same.
after the first ignition you can smell bad odours (owing to the drying of the glue used in the garnitures or of the paint) which disappear after
a brief using of the appliance. a good ventilation of the room should always be guaranteed.
ATTENTION: during the first lightings there could be a solid smokes condensation with a small escape of water from the
thermo-fireplace: this event will expire in a very short time but if it persists it will be necessary to check the chimney
draught.
To perform a correct first lighting of the products treated with paints for high temperature, it is necessary to know the following information:
• the construction materials of the involved products are not homogeneous, in fact there are simultaneously parts in cast iron, steel,
refractory material and majolica;
• the temperature to which the body of the product is subject is not homogeneous: from area to area, variable temperatures within the
range of 300°C - 500°C are detected;
• during its life, the product is subject to alternated lighting and extinguishing cycles in the same day, as well as to cycles of intense use or
of absolute standstill when season changes;
• the new appliance, before being considered seasoned has to be subject to many start cycles to allow all materials and paints to complete
the various elastic stresses;
• in detail, initially it is possible to remark the emission of smells typical of metals subject to great thermal stress, as well as of wet paint. This
paint, although during the manufacture it is backed at 250 °C for some hours, must exceed many times and for a given period of time the
temperature of 350 °C before becoming completely embedded in the metallic surfaces.
Therefore, it is extremely relevant to take these easy steps during the lighting:
1. Make sure that a strong air change is assured in the room where the appliance is installed.
2. during the first starts, do not load excessively the combustion chamber (about half the quantity indicated in the instructions manual) and
keep the product continuously on for at least 6-10 hours with the registers less open than the value indicated in the instructions manual.
3. Repeat this operation for at least 4-5 or more times, according to your possibilities.
4. Then load more and more fuel (following in any case the provisions contained in the installation booklet concerning maximum load) and,
if possible, keep the lighting periods long avoiding, at least in this initial phase, short on/off cycles.
5. during the first starts, no object should be leaned on the appliance and in detail on enamelled surfaces. enamelled surfaces must not be
touched during heating.
6. once the «break-in» has been completed, it is possible to use the product as the motor of a car, avoiding abrupt heating with excessive
loads.
After testing the proper working of the appliance, some days from the installation, it is possible to proceed with the
construction of its aesthetic covering.
WARNINg: during the surround building operations it must kept in mind possible and subsequent electrical installed parts
maintenance (fans, temperature probe, etc) and with hydraulic systems all parts connected to the thermo-fireplace.

LOW EMIssION FIRE LIgHTINg

smokeless combustion is a way of lighting a fire able to significantly reduce the emission of harmful substances. The wood burns gradually
from the top downwards, so combustion is slower and more controlled. Burnt gases pass through the high temperatures of the flame and
therefore burn almost completely.
place the logs in the hearth a certain distance apart as shown in the
top, or vertically in the case of tall narrow combustion chambers. place the fire starter module on top of the pile, arranging the first logs in the
module at right angles to the pile of wood.
Fire sTARTER MODULE. This fire starter module replaces a paper or cardboard starter. prepare four logs, 20 cm long with a cross section of 3
28
Picture 12. arrange the largest at the bottom and the smallest at the
ENgLIsH