Silverline 793759 Mode D'emploi page 6

GB
• Before drilling, check that there is sufficient clearance for the drill bit under the workpiece
• Use both hands when operating this tool
• Do not put pressure on the tool, to do so would shorten its service life
• Drill bits get hot during operation, allow to cool prior to handling them
• Never use your hands to remove sawdust, chips or waste close by the bit
• If you are interrupted when operating the drill, complete the process and switch off before
looking up
• Where possible, use clamps or a vice to hold your work
• Always disconnect the drill from the air supply before changing a bit
• Examine the chuck regularly for signs of wear or damage. Have damaged parts repaired by a
qualified Silverline service centre
• Always wait until the drill has come to a complete stop before putting it down
• On completion of the work, disconnect the tool from the air supply and remove bit from the
machine
• Periodically check all nuts, bolts and other fixings and tighten where necessary
Product Familiarisation
1 Chuck
2 Handle
3 Air Inlet ¼" BSP
4 Quick Connector
5 Forward/Reverse Lever
6 Trigger
Unpacking Your Tool
• Carefully unpack and inspect your tool. Fully familiarise yourself with all its features and
functions
• Ensure that all parts of the tool are present and in good condition. If any parts are missing or
damaged, have such parts replaced before attempting to use this tool
Intended Use
One speed drill, powered by compressed air from a compressor, with forward/reverse function. Uses
drill bits and other compatible accessories with a shaft diameter up to 9.5mm (3/8").
Note: This air drill does not feature a torque clutch and must therefore not be used for screw driving
or similar applications.
Before Use
Fitting the quick connector
Note: This tool is supplied with two different male airline quick connectors:
EQ-4 – commonly used in Europe
EN-6 – mainly used in the UK
EQ-4
Europe
• Please choose the connector that is compatible with the airline system you are using, and install
as outlined below:
1. Apply some PTFE tape (not included) to the screw threads of the Quick Connector (4). This will
help to maintain an air tight seal
Note: Apply PTFE tape tightly and in a clockwise direction, so it does not come off when the thread
is screwed into the tool.
2. Remove the protective plug from the air inlet
6
3. Using a spanner (not included) screw the quick connector into the air inlet located at the base of
the handle
4. Connect to airline, pressurise carefully and carry out a leak check (e.g. by spraying small
amounts of soapy water on to the outside of the connectors)
• Air lines fitted with matching female quick connectors will now be a push fit to the tool
Air supply connection
TO YOUR
NIPPLE
AIR TOOL
LEADER HOSE
• This tool should be connected to a clean, dry air supply with inline oiler and water separator
• Do not allow supply pressure to exceed the maximum stated (see 'Specifications')
• Ensure that water is drained from air system daily
• Ensure that all parts of the system (hoses, couplers, etc.) are correctly rated for the air pressure
to be used
Setting tool power
• The tool speed/power can be adjusted by decreasing/increasing the air supply pressure within
the range specified in 'Specifications' .
Fitting and removing drill bits and
accessories
WARNING: Always disconnect the tool from the air supply before fitting or removing drill bits or
other accessories.
WARNING: NEVER run the drill while tightening the chuck or changing the direction.
WARNING: Never install accessories with a maximum speed rating below the no load speed of
this tool.
1. Open the chuck by rotating the chuck collar anticlockwise
2. Insert the required drill bit or accessory
3. Close the chuck by rotating it clockwise. Tighten by hand
Note: Ensure the drill bit or accessory runs centrally and repeat above steps to correct the position of
the bit in the chuck if necessary.
Forward/reverse function
• For clockwise rotation ('forward') tilt the Forward/Reverse Lever (5) into the position labelled 'F'
• For anticlockwise rotation ('reverse') tilt the forward/reverse lever into the position labelled 'R'
WARNING: DO NOT operate the tool with the forward/reverse lever in a position between 'F' or 'R' , as
this may damage the internal mechanisms.
Operation
1. Select direction using the Forward/Reverse lever (5)
2. Hold the tool firmly by the Handle (2)
3. Press the Trigger (6) to operate the drill. Release the trigger to stop the machine.
Note: The air exhaust is located at the bottom of the handle. During operation, air will escape
directly next to the air inlet connection.
WARNING: Be aware that air tools may hold residual pressure after use. Always bleed air pressure
from the tool after shutting off air supply
Accessories
• Accessories for this tool, including drill and countersink bits, wire cup brushes and more, are
available from your Silverline stockist. Spare parts can be obtained from your Silverline dealer or
EN-6
www.toolsparesonline.com
UK
Cleaning
• Keep your tool clean at all times. Dirt and dust will cause internal parts to wear quickly, and
shorten the machine's service life. Clean the body of your machine with a soft brush, or dry cloth
IMPORTANT: There is very little that can go wrong with your air tool and it should be noted that
when an air tool fails to work it is generally because the internal workings have corroded due to
dirty, wet air and failure to follow the instructions given below.
Daily maintenance procedure: Disconnect from the air supply, pour the equivalent of a
tablespoon of oil into the air intake. Operate the machine at low speed to thoroughly lubricate all
WATER SEPARATION
QUICK COUPLER
NIPPLE
OILER
RECOIL HOSE
REGULATOR
DRAIN DAILY
AIR SUPPLY