Table des Matières

Publicité

Les langues disponibles
  • FR

Les langues disponibles

  • FRANÇAIS, page 23
10

PRESET

1. Preset mode
q Turn the EFFECTS ASSIGN switch !1 to select "OFF".
w The preset mode is available when the TAP button !5 is pushed for more than 2 seconds.
e Turn the MODE PARAMETERS knob !2 to select the preset item.
r After selecting an item, push the MODE PARAMETERS knob !2 to select the preset data.
t To change other preset items, repeat these steps.
y To exit from preset mode, press the TAP button !5 .
2. Preset items and data
The "*" mark next to the data indicates the default value.
(1)
EQ Mode : EQ sound can select Auto or Parametric.
EQMode : Auto* / Para.
(2)
High EQ Frequency :
When EQ mode is selected "Para.", you can select high range frequency of 3 band EQ 6 kHz to
20 kHz.
HEQFreq : xxx Hz (13 kHz*)
(3)
Middle EQ Frequency :
When EQ mode is selected "Para.", you can select middle range frequency of 3 band EQ 200 Hz
to 6 kHz.
MEQFreq : xxx Hz (1 kHz*)
(4)
Low EQ Frequency :
When EQ mode is selected "Para.", you can select low range frequency of 3 band EQ 20 Hz to
200 Hz.
LEQFreq : xxx Hz (100 Hz*)
(5)
High EQ Q :
When EQ mode is selected "Para.", you can select high range Q of 3 band EQ.
HI_EQ_Q : Wide / Normal* / Narrow
(6)
Middle EQ Q :
When EQ mode is selected "Para.", you can select middle range Q of 3 band EQ.
MIDEQ_Q : Wide / Normal* / Narrow
(7)
Low EQ Q :
When EQ mode is selected "Para.", you can select low range Q of 3 band EQ.
LOWEQ_Q : Wide / Normal* / Narrow
(8)
Headphone EQ :
Select EQ of headphone, High range boost, Low range boost or High + Low range boost.
H/P_EQ : Normal* / H_Boost / L_Boost / HLBoost
(9)
Channel Fader Curve : Select the startup curve of channel fader.
CHCurve : Slow / Normal* / Sharp
(10) Crossfader Curve : Set the startup curve of Crossfader.
CRCurve : Normal / Sharp*
(11) Auto BPM : Auto BPM displays when the CUE button !6 is pressed.
AutoBPM : ON / OFF*
(12) Talk Over Level : You can select decreased level of the Talk Over function.
T.Over : –6 dB / –10 dB / –20 dB*
(13) Effector Manual mode ON/OFF :
Setting of whether or not to perform the Manual parameter mode of the internal Effector.
Manual Eff. : ON / OFF*
(14) Echo2 (Normal Echo) ON/OFF :
Setting of whether or not to perform the Echo2 (Normal Echo) of the internal Effector.
Echo 2 : ON / OFF*
(15) Filter2 (Auto Filter) ON/OFF :
Setting of whether or not to perform the Filter2 (Auto Filter) of the internal Effector.
Filter 2 : ON / OFF*
(16) Pan ON/OFF :
Setting of whether or not to perform the Pan of the internal Effector.
Pan : ON / OFF*
(17) Trans ON/OFF :
Setting of whether or not to perform the Trans of the internal Effector.
Trans : ON / OFF*
(18) Key% ON/OFF :
Setting of whether or not to perform the Key of the internal Effector.
Key% ↑ ↓ : ON / OFF*
(19) Noise Gate (CH) :
Setting of the function for attenuating the noise of the signals output from channels 1 to 4.
N.Gate CH : OFF* / Low / Hi
(20) Noise Gate (MIC) :
Setting of the function for attenuating the noise of the MIC signals.
N.Gate Mic : OFF* / ON
NOTES:
• The Noise Gate function is a function for attenuating the noise on the analog circuitry using internal digital
signal processing. Set it as desired.
• With the Noise Gate Function, the sound may seem distorted, for example when low level input signals
are input or when the level of the input signals is set low with the GAIN control.
(21) Display the microprocessor version. ("xxxx" is a number.)
Version : Sysxxxx / Panxxxx / Dspxxxx
(22) Preset Clear : Set all the preset data back to factory defaults. ("P.Init?")
q To clear the PRESET data, push the MODE PARAMETERS knob !2 .
• "InitOK?" displays on the character display.
w Push the MODE PARAMETERS knob !2 again and start to clear the preset data.
• "Preset" and "Initial" are displayed on the character display while data clearing.
ENGLISH
13

Publicité

Table des Matières
loading

Table des Matières