Setup And Silent Modes; Selecting Modes; Muting The Microphone; Changing The Color Code - AKG WMS 4000 Mode D'emploi

Masquer les pouces Voir aussi pour WMS 4000:
Table des Matières

Publicité

Les langues disponibles
  • FR

Les langues disponibles

  • FRANÇAIS, page 26
Gain Screen: Input gain in dB.
2. To step through the above screens in reverse order, turn the jog switch briefly to the left.
In SETUP and SILENT modes, the various setup menus described in sections 3.4 through 3.8 come up
in the order shown below:
- Preset Menu
- Frequency Menu
- Battery Screen
- Gain Menu
• To toggle between LOCK mode and SETUP mode, push and hold the jog switch for approx. 1.5 sec-
onds.
In LOCK mode, the "LOCK" label will be shown on the display.
The transmitter is fully functional in SETUP mode, too. Remember, though, that settings may change
if you inadvertently actuate the jog switch.
The transmitter will revert to LOCK mode after about 15 minutes.
• To toggle between LOCK or SETUP mode and SILENT mode:
1. Switch power to the transmitter OFF.
2. Switch power to the transmitter ON by pushing and holding for approx. 1.5 seconds either the
ON/OFF button to enter LOCK mode or the jog switch to enter SILENT mode.
1. To mute the microphone, slide the MUTE switch (4) toward the outside of the transmitter. The status
LED (1) will change to red.
2. To switch the microphone back ON, slide the MUTE switch (4) toward the inside of the transmitter. The
status LED (1) will change to green.
The supplied Color Coding Kit includes pre-cut paper strips in various colors that you can assign to the
various channels of a multichannel system. You can write or print additional information (e.g., channel
number, frequency, performer's name, etc.) on each paper strip.
1. Unscrew the battery compartment cover (1) CCW from the transmitter.
2. Pull the color code holder (2) out of the transparent cover.
3. Remove the desired paper strip (3) from the color code sheet and place the paper strip (3) on the color
code holder (2).
4. Slide the color code holder (2) below the transparent cover to the stop.
5. Screw the battery compartment cover (1) back onto the transmitter CW.
In LOCK mode, the display constantly indicates the current battery capacity as a string of bars below the
frequency readout.
If the "BATT" label starts flashing, a dash appears instead of the bars, and the status LED changes to
red, replace the batteries or charge the BP 4000 battery pack as soon as possible.
You can check the remaining battery capacity at any time by turning the jog switch briefly to the left or
right one to three times (depending on the currently active screen). The battery capacity will be displayed
in hours and as a string of bars.
A handheld vocal microphone provides many ways of shaping the sound of your voice as it is heard over
the sound system.
The following sections contain useful hints on how to use your HT 4000 handheld transmitter for best
results.
Basically, your voice will sound the bigger and mellower, the closer you hold the microphone to your lips.
Moving away from the microphone will produce a more reverberant, more distant sound as the micro-
phone will pick more of the room's reverberation.
You can use this effect to make your voice sound aggressive, neutral, insinuating, etc. simply by changing your working
distance.
4 Operating Notes
Battery Screen: Battery
capacity in hours and as bar
graph. If the microphone is
ON, the "MUTE" label is off.
4.1.2 SETUP and SILENT
Modes

4.2 Selecting Modes

Note:

4.3 Muting the Microphone

Refer to fig. 1.

4.4 Changing the Color Code

Refer to fig. 4.

4.5 Replacing Batteries

Refer to fig. 3.

4.6 Microphone Technique

4.6.1 Working Distance and
Proximity Effect
Refer to fig. 5.
23

Publicité

Table des Matières
loading

Ce manuel est également adapté pour:

Ht 4000

Table des Matières