Input Activation; Input Deactivation; Low Battery Power Message - Bentel Security BTEL-3G Manuel D'installation

REMOTE PROGRAMMING BY TEXT MESSAGE
The dialler's features allow you to program one or more preset telephone numbers to which text messages will be sent
when specific events take place:
 Any alarm signals on one or more of the 4 inputs.
 Low Battery Test. 2 text messages can be programmed, one for malfunctions and one for resetting.
 Periodic sending of a text message at programmed intervals.
 Sending a text message to check the remaining credit.
Programing is performed by means the following text messages.
LED blinks three times when the BTEL-3G receives a valid programming SMS.

Input Activation

The BTEL-3G can send a text message to the numbers in the phone book when an event activating the inputs takes
place. To do this, send a programming text message in the following format:
#Installer PIN#INA#Input#Receiving Numbers#Message Text#
where the following are enclosed by # signs:
 Installer PIN; a numeric code of 5 digits (from 00000 to 99999).The factory default installer PIN is 11111.
 INA; the command text that programs the activation of inputs.
 Input; identifies the input (IN1, IN2, IN3, IN4 which correspond to inputs L1, L2, L3, and L4).
 Recipient Number; position of the telephone number in the phone book (see "Paramaters Management->Phone
Book Management "). To send the text message to multiple numbers in the phone book, separate the numbers with
a comma (for example "2,3,5" sends the text message to the telephone numbers stored under numbers 2, 3, and 5).
 Message Text ; type the text message to send (maximum 100 characters).To disable sending of the message not
type the text.

Input Deactivation

The BTEL-3G can send a text message to the numbers in the phone book when an event deactivating the inputs takes
place. To do this, send a programming text message in the following format:
#Installer PIN#IND#Input#Receiving Numbers#Message Text#
where the following are enclosed by # signs:
 Installer PIN; a numeric code of 5 digits (from 00000 to 99999).The factory default installer PIN is 11111.
 IND; the command text that programs the deactivation of inputs.
 Input; identifies the input (IN1, IN2, IN3, IN4 which correspond to inputs L1, L2, L3, and L4).
 Recipient Number; position of the telephone number in the phone book (see "Paramaters Management->Phone
Book Management "). To send the text message to multiple numbers in the phone book, separate the numbers with
a comma (for example "2,3,5" sends the text message to the telephone numbers stored under numbers 2, 3, and 5).
 Message Text ; type the text message to send (maximum 100 characters).To disable sending of the message not
type the text.

Low Battery Power Message

When battery power is low, a text message can be sent to a preset telephone number. To do this, send a programming
text message in the following format:
#Installer PIN#BAT#Receiving Number#Low Battery Power Text#Battery Reset Text#Enable#
where the following are enclosed by # signs:
 Installer PIN; a numeric code of 5 digits (from 00000 to 99999).The factory default installer PIN is 11111.
 BAT; the program command to send a message informing that the battery power is low.
 Recipient Number: type the phone number of the recipient (not its position in the phone book). The telephone
number may also be a number not found in the phone book.
 Low Battery Power Text ; type the text message informing the recipient that the Battery Power is Low (maximum
50 characters).
 Reset Text ; type the text message to be sent to notify that the Battery Has Been Reset (maximum 50 characters).
 Enable; type 1 to enable the sending of text messages or 0 to disable(in this case the fields Receiving Number,
Low Battery Power Text, and Reset Text will be disregarded).
3G/2G Telephone dialler
EN
17