EINHELL RT-SM 430 U Mode D'emploi D'origine page 25

Anleitung_RT_SM_430_U_SPK1:_
7.7 Changing the saw blade (Fig. 1, 37 – 40)
Remove the power plug!
Swing the machine head (4) upwards and lock it
n
in this position using the locking pin (27).
Press the release lever (3) and swing up the saw
n
blade guard (6) to the point where the recess in
the saw blade guard (6) is above the flange bolt
(39).
Press the saw shaft lock (5) with one hand while
n
holding the wrench (P) on the flange bolt (39)
with the other.
Firmly press on the saw shaft lock (5) and slowly
n
rotate the flange bolt (39) in clockwise direction.
The saw shaft lock (5) engages after no more
than one rotation.
Now, using a little more force, slacken the flange
n
bolt (39) in the clockwise direction.
Undo the flange bolt (39) and remove it and them
n
take off the outer flange (40).
Take the saw blade (7) off the inner flange and
n
pull it out downwards.
Carefully clean the flange bolt (39), outer flange
n
(40) and inner flange.
Fit and fasten the new saw blade (7) in reverse
n
order.
Important. The cutting angle of the teeth, in other
n
words the direction of rotation of the saw blade
(7) must coincide with the direction of the arrow
on the housing.
Check to make sure that all safety devices are
n
properly mounted and in good working condition
before you begin working with the saw again.
Important. Every time that you change the saw
n
blade, check to see that it spins freely in the table
insert (12) in both perpendicular and 45° angle
settings.
Important. The saw blade (7) must be changed
n
and aligned correctly.
7.8 Storage compartment for spare saw blade
(Fig. 41 / Item 28)
The saw is equipped with a storage compartment (28)
for a spare saw blade. To open the storage
compartment (28), pull the locking knob (29) on the
rear of the saw while pulling the storage compartment
(28) out at the same time.
7.9 Using the laser (Fig. 42 – 43 / Item 21)
To switch on: Move the laser ON/OFF switch (42)
into the "I" position to switch on the laser (21). A laser
line is projected on to the workpiece you wish to
machine, providing an exact guide for the cut.
To switch off: Move the laser ON/OFF switch (42)
into the "0" position.
Adjusting the laser: Undoing the screws (41)
slightly allows the laser to be adjusted if necessary.
21.03.2012 9:33 Uhr Seite 25
Tighten the screws again after you have completed
the adjustment work. Important. Never look directly
into the LED light!
Replacing the battery: Ensure that laser (21) is
switched off. Remove the battery compartment cover
(43). Remove the spent batteries and replace them
with new ones (2 x 1.5 V type R02, LR 03 Micro,
AAA). Check that the battery terminals are positioned
correctly. Close the battery compartment again.
7.10 Transport (Fig. 1 – 3)
Tighten the locking grip (14) to lock the turntable
n
(17).
Press the release lever (3), push the machine
n
head (4) to the rear and lock it with the locking
bolt (27). The saw is now locked in its lower
position.
Secure the drag function of the saw in its rear
n
position using the fixing screw for the drag guide
(25).
Carry the machine using the fixed saw bench (18)
n
or, if the saw is mounted on the base frame, using
the appropriate trough handles on the base
frame.
Follow the instructions set out in point 6.2 to erect
n
the machine again.
7.11 Battery disposal
Recycle the packaging. Ensure that you sort the
materials for recycling. Do not dispose of batteries in
household waste. All consumers have a duty to
dispose of batteries properly at the appropriate
collection points. Send your spent batteries to iSC
GmbH, Eschenstrasse 6 in D-94405 Landau. You can
then be sure that the equipment will be correctly
disposed of by the manufacturer.
8. Replacing the power cable
If the power cable for this equipment is damaged, it
must be replaced by the manufacturer or its after-
sales service or similarly trained personnel to avoid
danger.
GB
25