EINHELL RT-SM 430 U Mode D'emploi D'origine page 24

Anleitung_RT_SM_430_U_SPK1:_
GB
Place the piece of wood to be cut at the stop rail
n
(11) and on the turntable (17).
Lock the material with the clamping device (8) on
n
the fixed saw bench (18) to prevent the material
from moving during the cutting operation.
Push down the release lever (3) to release the
n
machine head (4).
Press the ON/OFF switch (2) to start the motor.
n
If the drag guide (25) is fixed: Move the machine
n
head (4) downwards evenly and with gentle
pressure using the handle (1) until the saw blade
(7) has cut through the workpiece.
If the drag guide (25) is not fixed:
n
Pull the machine head (4) as far as possible
forwards and then lower it evenly and with gently
pressure using the handle (1). Now push the
machine head (4) slowly and evenly right to the
rear until the saw blade (7) has cut right through
the workpiece.
When the cutting operation is completed, move
n
the machine head (4) back to its upper (home)
position and release the ON/OFF button (2).
Important. The integral resetting springs will
automatically lift the machine head. Do not simply let
go of the handle (1) after cutting, but allow the
machine head (4) to rise slowly, applying slight
counterpressure as it does so.
7.2 Crosscut 90° and turntable 0° - 45°
(Fig. 1 – 3, 31)
The crosscut saw can be used to make angular cuts
of 0°- 52° to the left and 0 – 60° to the right relative to
the stop rail.
Release the turntable (17) by slackening the
n
locking grip (14).
Press the locking lever (13), turn the turntable (17)
n
and scale pointer (15) to the desired angular
setting on the dial (16) and lock into place with
the locking grip (14). The saw has locking
positions at angular positions of -45°, -30°, -22,5°,
-15°, 0°, 15°, 22,5°, 30°, 45° and 60° at which the
locking lever can be engaged.
Retighten the locking grip (14) to secure the
n
turntable (17) in place.
Cut as described under section 7.1.
n
7.3 Miter cut 0°- 45° and turntable 0°
(Fig. 1 – 3, 32)
The crosscut saw can be used to make miter cuts of
0° - 45° in relation to the work surface.
Remove the clamping device (8) if necessary or fit
n
it on the opposite side of the fixed saw bench
(18).
Move the machine head (4) to its upper position.
n
Fasten the turntable (17) in 0° position.
n
Undo the locking screw (22) and use the handle
n
24
21.03.2012 9:33 Uhr Seite 24
(1) to tilt the machine head (4) to the left until the
pointer (20) points to the required angle on the
scale (19).
Retighten the locking screw (22) and make the cut
n
as described in section 7.1.
7.4 Miter cut 0°- 45° and turntable 0° - 45°
(Fig. 1 – 3, 33)
The crosscut saw can be used to make miter cuts of
0°- 45° to the left relative to the work surface and, at
the same time, 0° - 52° to the left or 0° - 60° to the
right of the stop rail (double miter cut).
Remove the clamping device (8) if necessary or fit
n
it on the opposite side of the fixed saw bench
(18).
Move the machine head (4) to its upper position.
n
Release the turntable (17) by slackening the
n
locking grip (14).
Use the handle (1) to adjust the turntable (17) to
n
the angle required (in this connection see also
section 7.2).
Retighten the locking grip (14) to secure the
n
turntable in place.
Undo the locking screw (22) and use the handle
n
(1) to tilt the machine head (4) to the left until it
coincides with the required angle value (in this
connection see also section 7.3).
Re-tighten the locking screw (22).
n
Cut as described under section 7.1.
n
7.5 Limiting the cutting depth (Fig. 34)
The cutting depth can be infinitely adjusted using
n
the screw (34). Undo the knurled nut on the screw
(34) and move the stop for limiting the cutting
depth (35) to the outside. Set the required cutting
depth by tightening or undoing the screw (34) and
then tighten the knurled nut on the screw (34).
Check the adjustment by making a test cut.
n
7.6 Chip collection box (Fig. 35 – 36 / Item 23)
The saw is equipped with a chip collection box (23)
for sawdust and chips. The chip collection box (23)
can be connected to the extractor adaptor (33).
To empty the chip collection box (23), open it as
shown in Fig. 37 and carefully tap it to empty the
contents.
A suitable dust extraction device may also be
connected to the extractor adapter (33).