EINHELL RT-SM 430 U Mode D'emploi D'origine page 23

Anleitung_RT_SM_430_U_SPK1:_
tilt the machine head (4) to the left by up to 45°.
If the saw is used without a base frame, the
n
support foot (32) is designed to ensure that the
saw cannot tip forwards during use. To do this,
unscrew the support foot (32) until it touches the
support surface of the saw.
6.3 Assembling the base frame and bolting the
saw to the base frame (Fig. 4 – 24)
1. Place the support feet (A) from underneath into
the intermediate struts (C) as shown in Fig. 7.
Ensure that the rubber feet are aligned on the
support feet (A) so that their support surfaces are
straight.
2. Bolt the support feet (A) to the intermediate struts
(C) as shown in Fig. 8 – 9 using the screws (N),
washers (H) and nuts (G).
3. Guide the side parts (B) from the top over the
intermediate struts (C) (Fig. 10).
4. Bolt the side parts (B) to the intermediate struts
(C) using three screws (L), washers (K) and nuts
(I) at each connection point (Fig. 11 – 12).
5. Place the two cross struts (E) as far as possible
into the corresponding recesses in one of the
intermediate struts (C) (Fig. 13). Bolt the bottom
cross struts (E) to the intermediate strut (C) using
two screws (L), washers (K) and nuts (I) at each
connection point, as shown in Fig. 14 – 15.
6. On the same half of the base frame, guide the two
top cross struts (F) as far as possible into the
corresponding recesses in the side part (B) (Fig.
16). Connect one corner reinforcement (D) to
each of the recesses in the side part (B). Please
note that the corner reinforcements (D) only fit on
one side of the base frame. This is the case if the
holes in the side part (B), top cross struts (F) and
corner reinforcements (D) line up (Fig. 17).
7. Fasten both saw mounts onto the same base
frame (J) as shown in Fig. 18. Please note that
the saw mounts (J) only fit on one side of the
base frame. This is the case if the holes in the
side parts (B), the upper cross-struts (F), corner
braces (D) and saw mounts (J) are aligned. (Fig.
18).
8. Now screw the upper cross struts (F), corner
braces (D), side parts (B) and saw mounts (J)
together, as shown in Figs. 18-19 with 2 screws
(L), washers (K) and nuts (I) each, together.
9. Connect the two halves of the base frame so that
the bottom and top cross struts (E, F) fit into the
corresponding recesses on the side part (B) and
intermediate strut (C) (Fig. 20).
10. Bolt the bottom cross struts (E) to the second half
of the base frame as described in 5 (Fig. 21/1).
11. Bolt the top cross struts (F) to the second half of
the base frame as described in 6 (Fig. 21/2).
21.03.2012 9:33 Uhr Seite 23
12. Pull the four rubber buffers (32) off the underside
of the saw (Fig. 22).
13. Set the saw onto the base frame, so that the
holes in which there are rubber stops (32) are
aligned with the 4 holes on the upper side of the
saw mount (J). Now insert the 4 screws (M) from
above through the saw feet and screw the saw to
the saw mount (J) (Fig. 23-24)
6.4 Final adjustment of the stop for crosscut 90°
(Fig. 1, 25 – 27)
Fasten the turntable (17) in 0° position.
n
Undo the securing screw (22) and tilt the machine
n
head (4) as far to the right as possible using the
handle (1).
Place the 90° angular stop (a) between the saw
n
blade (7) and the turntable (17).
Undo the counter nut (36) and adjust the
n
adjustment screw (38) until the angle between the
saw blade (7) and the turntable (17) is 90°.
Retighten the counter nut (36) to secure this
n
setting.
Finally check the position of the pointer (20) on
n
the scale (19). If necessary undo the pointer (20)
with a Philips screwdriver, set it to the 0° position
on the scale (19) and tighten the retaining screw
again.
An angular stop is not supplied.
n
6.5 Final adjustment of the stop for meter cut 45°
(Fig. 1, 25, 28 – 29)
Fasten the turntable (17) in 0° position.
n
Undo the securing screw (22) and tilt the machine
n
head (4) to the right to an angle of 45° using the
handle (1).
Place the 45° stop angle (b) between the blade
n
(7) and the turntable (17).
Adjust the adjustment screw (37) until the angle
n
between the saw blade (7) and the turntable (17)
is 45°.
An angular stop is not supplied.
n
7. Operation
7.1 Crosscut 90° and turntable 0° (Fig. 1 – 3, 30)
For cutting widths up to 100 mm it is possible to fix
the saw's drag function in its rear position with the
fixing screw for drag guide (25). If the cutting width
exceeds 100 mm you must ensure that the fixing
screw for the drag guide (25) is undone and that the
machine head (4) can be moved.
Move the machine head (4) to its upper position.
n
Use the handle (1) to push back the machine
n
head (4) and fix it in this position if required
(dependent on the cutting width).
GB
23