Jenn-Air JMW2430 Guide D'utilisation Et D'entretien page 22

To Use Temperature Probe:
1. Insert the probe into the food item. For meats, the probe tip
should be located in the center of the thickest part of the
meat and not into the fat or touching the bone.
2. Place food in oven.
3. Connect the temperature probe to the jack inside the oven.
Keep probe as far away from the heat source as possible.
4. Close the oven door.
5. From the Select Mode menu, touch the MORE button until
Probe is shown. Press the quickset pad next to Probe.
6. From the Probe Cooking menu, select Bake, Convect Bake,
Convect Roast or Food Temperature Guide by touching the
quickset pad next to the chosen mode.
7. Set the Probe temperature for Bake, Convect Bake or
Convect Roast. The temperature must be between 130°F
(54°C) and 185°F (85°C). The default value is 160ºF (71ºC).
8. Choose the default oven temperature or set the desired
temperature by selecting the Oven Temp option and then
entering the desired temperature.
9. If Food Temperature Guide is selected, select the type of
food: beef, fresh; chicken; ham, precooked; lamb; pork;
turkey or veal.
NOTE: Some foods may require additional selections.
10. Select the doneness level: medium rare, medium or well-
done, or set the probe temperature if available.
NOTE: An appropriate probe temperature has been set as the
default temperature for your selected doneness. Food should
be removed from the oven when the probe notifies you,
covered and allowed to stand for 10-15 minutes. The
10-15 minutes rest allows the temperature of the food to
increase to your desired doneness level.
11. To set a desired cooking temperature, select the Oven Temp
option and enter the desired temperature. The temperature
must be set between 170°F (77°C) and 550°F (288°C).
12. (Optional) To set a delayed start, press the quickset pad next
to Delay Start and set desired time. See "Delay Start" for
additional information.
13. Press START to begin cooking.
14. Press CANCEL OVEN (CANCEL UPPER or CANCEL LOWER,
on double models) to turn off the oven.
Delay Start
WARNING
Food Poisoning Hazard
Do not let food sit in oven more than one hour before
or after cooking.
Doing so can result in food poisoning or sickness.
NOTE: Do not use Delay Start for items that require a preheated
oven, such as cakes, cookies and breads. If food is in the oven
during preheat, it may become overcooked.
Delay Start allows the oven(s) to be set to turn on at a certain
time of day. This feature can be set to use with the Cook Timer,
while using the probe, or as a delayed start with no Cook Timer.
Delay Start should not be used for food such as breads and
cakes because they may not bake properly.
22
Delay Start is available in any cycle that has a Delay Start button.
You may need to select Set Cook Timer to access the Delay Start
option. The Set Cook Timer option is available on the
Temperature screen.
To Set a Delay Start:
1. From any cycle with the Delay Start button available, press
the quickset pad next to Delay Start and set start time.
2. Set time by touching the quickset pads.
3. Press START.
NOTE: When no cook timer is set, the oven will automatically
turn off after cooking 12 hours. The Sabbath Mode disables
the 12-hour shutoff.
Delay with Cook Timer:
1. After programming the cook timer, select Delay Start and use
the quickset pads to select the desired start time. The end
time should equal the start time plus the Cook Timer.
2. Press START.
NOTE: When the cook timer ends, the oven will turn off.
Delay with Probe:
WARNING
Burn Hazard
Use an oven mitt to remove temperature probe.
Do not touch broil element.
Failure to follow these instructions can result in burns.
1. If Delay with Probe is chosen, use the quickset pads to select
the desired start time. Because the probe controls the end
time, an end time will not be displayed.
2. The oven will automatically keep the food warm when the
probe reaches the target temperature.
3. Press START.
Button Lock
The Button Lock allows all the buttons to be locked.
To Activate the Button Lock:
1. From the Select Mode menu, touch the MORE button until
Button Lock appears. Press the quickset pad next to it.
2. While the buttons are locked, there is a "locked" icon on the
idle screen.
To Deactivate the Button Lock:
1. If any button was pressed, an unlock message will appear on
the screen.
2. To unlock, press and hold the START button for 3 seconds.