SLV Elektronik 230736 Mode D'emploi page 3

INSTALLATION MANUAL for WALL FITTING
230736/46
ONLY FOR THE ELECTRICIAN!
The installation may only be carried out by an approved
electrician, who is familiar with valid directives and
regulations!
Explanation of the safety warnings:
immediate dangerous situation leading to death or
DANGER:
severe injuries when not avoided.
possible dangerous situation leading to death or
WARNING:
severe injuries when not avoided.
possible dangerous situation leading to injuries or
CAUTION:
material damage when not avoided.
In case of disregarding this manual the warranty will be void!
Pay also absolute attention the NOTES ON SAFETY on the
backside!
1. INSTALL AS DIRECTED
This product serves exclusively lighting purposes and may:
only be connected to a voltage of 230V ~50Hz.
only be operated when firmly mounted.
not be exposed to strong mechanical loads or to strong
contamination.
only be installed and operated after a condition inspection if the
product is dirty or has been moistened through storage.
not be modified or converted.
2. UNPACKING
Consignment:
Three protective tubes Fastening materials
Carefully take the product out of the packaging removing any
transport safeguards.
Before disposal of the packaging material make sure that all
components of the product are removed.
WARNING
Inspect the product for loose parts inside the housing. When there are
loose parts inside the housing and these are not explicitly described the
product may not be installed or operated.
Parts that may be touched are maybe voltage-carrying. Danger of
electric shock!
3. INSTALLATION
WARNING
Switch off the mains or respectively the connection lead before doing
.
any works
There exists mortal danger from an electric shock.
Use only accessory parts, which are supplied with the product or are
described as accessories!
Otherwise the product or the whole installation may not be secure.
Danger for life or danger of fire may exist!
Installation place
The product is solely suited for wall installation.
Make sure that the product is mounted on a stable, even and tilt-
fixed background.
WARNING
Use the supplied fastening material only when it is suited for the
installation background. If this is not the case use only fastening material
suiting the installation background.
When using fastening material that is not suitable there may be danger
from falling objects.
Separate Installation Steps
Remove the mounting plate from the canopy by loosening the two
screws on the side of the canopy.
Determine the place of installation and mark the holes to be drilled. Note
that the cable outlet of the mains supply corresponds with the cable inlet
of the fixture. Do not damage the power supply line, e.g. by drilling,
screws or strong bending.
Direct the mains lead through the rubber gasket.
Equip each fastening screw with a washer and a gasket.
Fasten the mounting plate to the mounting surface.
Electrical Connection
The product must be able to be separated by an all pole separation
from the current supply.
Equip the three wire ends with protective tubes.
For electric connection attach the black or brown wire (live conductor)
of the mains supply with the clamp L and the blue wire (neutral
conductor) of the mains supply with the clamp N. The green-yellow
wire (protective conductor) of the mains supply has to be tightly
screwed into the earth clamp of the product.
Now fasten the canopy back to the mounting plate. Note the proper fit of
the gasket.
Inserting the light source: Screw of the bulb cover(s). Touch energy-
saving-lamps on the plastic housing, not on the bulb glass. Screw the
bulb jnto the socket. Screw the bulb cover (s) back on tightly. Note the
proper fit of the gasket.
Ensure that the light fixture holds securely!
The product is now ready for operation.
4. FIRST OPERATION
On the first operation check if the product functions properly!
DANGER
In case of a malfunction you may NOT touch the product or operate it
further. Disconnect the product from the power supply by an external
switch or by the fuse.
If touched or further operated there is danger from electric shock,
burning, or fire.
A malfunction exists when:
visible damages appear.
the product does not work properly (e.g. flickering).
smoke, steam or crackling sounds appear.
smell of burning is recognisable.
an overheating is recognisable (e.g. by discolouration of adjacent
surfaces).
Operate the product only after maintenance and examination by an
approved electrician!
Notice for the electrician:
It is your responsibility to hand out the user manual on the reverse
side to the end user.
ONLY FOR THE ELECTRICIAN!
b a