Working Advice; Maintenance And Service; Maintenance And Cleaning; After-Sales Service And Application Service - Bosch Uneo Notice Originale

OBJ_BUCH-605-005.book Page 15 Tuesday, March 19, 2013 10:07 AM
Position for hammer drilling in concrete or
stone
Position for drilling without impact in wood,
metal, ceramic and plastic as well as for
screwdriving
Reversing the rotational direction (see figure D)
 Actuate the rotational direction switch 8 only when the
machine is at a standstill.
The rotational direction switch 8 is used to reverse the rota-
tional direction of the machine. However, this is not possible
with the On/Off switch 9 actuated.
Right Rotation: For drilling and driving in screws, push the
rotational direction switch 8 left to the stop.
The indicator for right rotation 6 lights up when the
On/Off switch 9 is actuated and the motor is running.
Left Rotation: For loosening and unscrewing screws and
nuts, press the rotational direction switch 8 through to the
right stop.
The indicator for left rotation 7 lights up when the
On/Off switch 9 is actuated and the motor is running.
Switching On and Off
To start the machine, press the On/Off switch 9 and keep it
pressed.
To switch off the machine, release the On/Off switch 9.
For low temperatures, the power tool reaches the full ham-
mer/impact capacity only after a certain time.
To save energy, only switch the power tool on when using it.
Setting the Speed/Impact Rate
The speed/impact rate of the switched on power tool can be
variably adjusted, depending on how far the On/Off switch 9
is pressed.
Light pressure on the On/Off switch 9 results in low speed/im-
pact rate. Further pressure on the switch increases the
speed/impact rate.
Battery Charge-control Indication
The battery charge-control indicator 5 indicates the charge
condition of the battery for a few seconds when the On/Off
switch 9 is pressed through halfway of fully.
LED
Continuous lighting, green
Continuous lighting, red
Temperature Dependent Overload Protection
When using as intended for, the power tool cannot be subject
to overload. When the load is too high or the allowable battery
temperature of 70 °C is exceeded, the electronic control
switches off the power tool until the temperature is in the op-
timum temperature range again.
Bosch Power Tools
Additionally, the battery charge-control indicator 5 flashes
green and red at the same time until the On/Off switch 9 is re-
leased.

Working Advice

 Apply the power tool to the screw/nut only when it is
switched off. Rotating tool inserts can slip off.

Maintenance and Service

Maintenance and Cleaning

 For safe and proper working, always keep the machine
and ventilation slots clean.
 Before any work on the machine (e. g., maintenance,
tool change, etc.) as well as during transport and stor-
age, set the rotational direction switch to the centre
position. Unintentional actuation of the On/Off switch can
lead to injuries.
 A damaged dust protection cap should be changed im-
mediately. We recommend having this carried out by
an after-sales service.
If the replacement of the supply cord is necessary, this has to
be done by Bosch or an authorized Bosch service agent in or-
der to avoid a safety hazard.
When the battery is no longer operative, please refer to an au-
thorised after-sales service agent for Bosch power tools.

After-sales Service and Application Service

In all correspondence and spare parts order, please always in-
clude the 10-digit article number given on the type plate of
the machine.
Our after-sales service responds to your questions concern-
ing maintenance and repair of your product as well as spare
parts. Exploded views and information on spare parts can al-
so be found under:
www.bosch-pt.com
Bosch's application service team will gladly answer questions
concerning our products and their accessories.
Great Britain
Robert Bosch Ltd. (B.S.C.)
P.O. Box 98
Broadwater Park
North Orbital Road
Denham
Uxbridge
UB 9 5HJ
Capacity
Tel. Service: (0844) 7360109
> 30%
Fax: (0844) 7360146
≤ 30% E-Mail: boschservicecentre@bosch.com
English | 15
2 609 007 217 | (19.3.13)