Working Advice; Maintenance And Service; Maintenance And Cleaning; After-Sales Service And Application Service - Bosch GBH 5-40 DCE Professional Notice Originale

OBJ_BUCH-1742-004.book Page 14 Friday, August 19, 2016 2:47 PM
14 | English
For low temperatures, the power tool reaches the full ham-
mer/impact capacity only after a certain time.
Setting the Speed/Impact Rate
The electronic control enables stepless speed and impact
preselection in accordance with the material to be worked.
The constant electronic control keeps the preselected speed
and impact rate nearly constant between no-load and load
conditions.
When plugging the plug into the socket outlet or after a power
failure, the constant electronic control automatically sets the
highest speed and impact rate. This ensures working at opti-
mum performance despite too low preadjustment of the
thumbwheel 7.
– Select the impact rate with the thumbwheel 7 according to
the material.
The data in the following table are recommended values.
Application
Working roughcast/light building materials
Removing tiles
Working brick
Working concrete
Overload Clutch
 If the tool insert becomes caught or jammed, the drive
to the drill spindle is interrupted. Because of the forces
that occur, always hold the power tool firmly with both
hands and provide for a secure stance.
 If the power tool jams, switch the machine off and loos-
en the tool insert. When switching the machine on with
the drilling tool jammed, high reaction torques can oc-
cur.
Changing the Chiselling Position (Vario-Lock)
The chisel can be locked in 12 positions. In this manner, the
optimum working position can be set for each application.
– Insert the chisel into the tool holder.
– Turn the mode selector switch 3 to the position "Vario-
Lock" (see "Setting the operating mode", page 13).
– Turn the tool holder to the desired chiselling position.
– Turn the mode selector switch 3 to the position "Chisel-
ling". With this, the tool holder is locked.
 For chiselling, the mode selector switch 3 must always
be set to the position "Chiselling".

Working Advice

 Before any work on the machine itself, pull the mains
plug.
Vibration Damper
The integrated vibration damper reduces occurring vibra-
tions.
1 609 92A 2GB | (19.8.16)
The soft grip handle increases the safety against slipping off
and thus provides for a better grip and handling of the power
tool.

Maintenance and Service

Maintenance and Cleaning

 Before any work on the machine itself, pull the mains
plug.
 For safe and proper working, always keep the machine
and ventilation slots clean.
 A damaged dust protection cap should be changed im-
mediately. We recommend having this carried out by
an after-sales service.
If the replacement of the supply cord is necessary, this has to
be done by Bosch or an authorized Bosch service agent in or-
der to avoid a safety hazard.
Thumbwheel
Service Indicator 8
Position
When the carbon brushes are worn out, the machine switches
itself off. This is indicated approx. 8 hours beforehand by the
lighting or blinking of the service indicator 8. The machine
must then be sent to an after-sales service agent. Addresses
are listed in the Section "After-sales Service and Application
Service".
Stand-by Indicator 9
When the mains plug is plugged in and mains voltage is given,
the stand-by indicator 9 must be lit. When the machine can-
not be switched on despite lit stand-by indicator 9, it must be
sent to an after-sales service agent; for addresses, see sec-
tion "After-sales Service and Application Service", page 14.

After-sales Service and Application Service

Our after-sales service responds to your questions concern-
ing maintenance and repair of your product as well as spare
parts. Exploded views and information on spare parts can al-
so be found under:
www.bosch-pt.com
Bosch's application service team will gladly answer questions
concerning our products and their accessories.
In all correspondence and spare parts orders, please always
include the 10-digit article number given on the nameplate of
the product.
Great Britain
Robert Bosch Ltd. (B.S.C.)
P.O. Box 98
Broadwater Park
North Orbital Road
Denham
Uxbridge
UB 9 5HJ
At www.bosch-pt.co.uk you can order spare parts or arrange
the collection of a product in need of servicing or repair.
Tel. Service: (0344) 7360109
E-Mail: boschservicecentre@bosch.com
Bosch Power Tools