Using The Saw - Scheppach HS105 Traduction Des Instructions D'origine

8.3 Riving knife set-up (Fig. 9/10/11)
m Warning! Disconnect
The set-up of the riving knife (6) must be checked
before each use.
1. Set the saw blade (5) to the max. cutting depth, put
it in the 0° position and lock it. .
2. Remove the table insert (6) (Fig. 9)
m Warning! For transport reasons, the riving
knife (6) was fixed in the lower position before
initial commissioning. Only work with the ma-
chine if the riving knife (6) is in the upper posi-
tion. Fitting the riving knife (6) in the upper posi-
tion is as follows:
3. Loosen the locking handle (23) and push the riving
knife (6) in the upper position (Fig. 10).
4. The gap between the saw blade (5) and the riving
knife (6) should be a maximum of 5 mm (Fig. 11).
5. Re-tighten the mounting screw (23) and fix the table
insert (6).
8.4 Saw blade guard assembly (Fig. 12)
1. Place the saw blade guard (2) including the bolt (24)
on the riving knife (4) from above so that the bolt is
tight in the slot of the riving knife (4).
2. Do not tighten the bolt (24) too much; the saw blade
guard (2) must be able to move freely.
3. Place the extraction hose (3) on the extraction adapt-
er on the rear of the machine and on the extraction
nozzle of the saw blade guard (2).
4. Disassembly takes place in reverse order.
Warning!
Before starting to saw, lower the saw blade guard
(2) on to the work piece.
8.5 Saw blade assembly/replacement (Fig. 9/12/13)
1. Warning! Disconnect the mains supply and wear
safety gloves.
2. Disassemble the saw blade guard (2) (Fig. 12).
3. Remove the table insert (6) (Fig. 9).
4. Loosen the nut by placing the open-ended spanner
(f) on the nut and countering with another open-end-
ed spanner (f) on the flange (Fig. 13).
5. Warning! Turn the nut in the rotational direction of
the saw blade.
6. Remove the outer flange and pull the old saw blade
from the inner flange, with a diagonally downwards
movement.
7. Carefully clean the saw blade flange with a wire brush
before fixing the new saw blade.
8. Insert the new saw blade in reverse order and tighten
it.
Warning! Observe the rotational direction; the
teeth have to point in the direction of rotation, i.e.
forwards.
9. Attach the table insert (6) and the saw blade guard
(2) again and set them.
10. Before working with the saw again, check the func-
tionality of the guards.
 www.scheppach.com  service@scheppach.com  +(49)-08223-4002-99  +(49)-08223-4002-58  www.scheppach.com  service@scheppach.com  +(49)-08223-4002-99  +(49)-08223-4002-58
the mains cable!

9. Using the saw

9.1 On/Off switch (Fig. 14)
- The saw can be switched on by pressing the green
pushbutton (11) „I".
- The red pushbutton (11) „0" has to be pressed to switch
off the saw.
9.2 Cutting depth (Fig. 14)
Turn the round handle (8) to set the blade to the required
cutting depth.
- Turn anti-clockwise: larger cutting depth
- Turn clockwise: smaller cutting depth
After each new adjustment it is advisable to carry out a
trial cut in order to check the set dimensions.
9.3 Setting the angle (Fig. 14)
With the table saw you can make diagonal cuts to the left
oriented to the stop bar from 0 ° to 45 °.
m Check before each cut, that between the stop bar (e),
cross-stop (13) and the saw blade (5) a collision is not
possible.
- Loose the fixing handle (9).
- Set the required angle on the scale.
- Lock the fixing handle (9) again in the required angle
position.
9.4 Working with the rip fence
9.4.1 Setting the fence height (Fig. 15)
- The fence rail (25) of the rip fence (7) has two guiding
surfaces with different heights.
- Depending on the thickness of the material to be cut,
the higher side of the fence rail (25) has to be used for
thick material (work piece thickness above 25 mm) and
the lower side of the fence rail for thin material (work
piece thickness below 25 mm).
- For the adjustment, loosen the bolts on the side of the
rip fence (7) and push the fence rail (25) on the guide,
depending on the required position.
- Tighten the bolts again.
9.4.2 Rip fence assembly (Fig. 16)
- Fix the rip fence (7) by placing it at the back and pulling
the locking lever (23) down.
- For disassembly, pull the locking lever up and remove
the rip fence (7).
- The locking force of the rip fence can be set with the
rear knurled nut.
9.4.3 Setting the cutting width (Fig. 17)
- The rip fence (7) must be used for lengthwise cutting
of wood.
- Place the rip fence (7) on the guide rail (12) to the right
or left of the saw blade.
- On the guide rail for the rip fence (12) there are 2 scales
(27/28) which display the gap between the fence rail
(25) and the saw blade (5).
27 І 60