Assembly - Scheppach HS520 Traduction Des Instructions D'origine

8-13 Accessories bag enclosed, containing:
29x lenticular flange head screw M8x16
29x locking nut M 8
2x hexagon screw M6
2x locking nut M6
2x washer D 20 mm
2x lock washer without cap D 18 mm
2x locking nut M 4
2x fillister head screw M 4x610
1x cover panel with clinch stud
2x plastic wascher
1x pivot bushing, galvanised
1x hexagon nut, self-locking M 6
1x hexagon screw M 5x12
1x collar bushing
1x hexagon nut, self-locking M5
4x mushroom head screw M6x12
4x washer D6
4x hexagon nut, self-locking M6
Additional accessories bag enclosed for protective flap with handle (Fig. 18)
2x saw guard
1x tension spring
2x hexagon screw M8x35
2x hexagon nut M8
6x hexagon nut, self-locking
1x hexagon screw M8x12
6x Philips screw M4x10
6x locking nut M4
3x hexagon screw M8x20
3x collar bushing D 8mm
3x washer D 8mm

8. Assembly

For packaging reasons, the swivel log saw does not come fully assembled. It must be assembled on a com-
pletely level surface.
A. Place the packaging, cardboard or similar on the floor to prevent damage. Remove the base frame from the packaging
and position the machine with the swivel side on top (Fig. A).
B. Lift wheel axle slightly, slide one washer (10) and one wheel (7) (for external side see Fig. B3, B4) onto the axle on
each side. Fit lock washer (11) on the axle with the saw blade wrench and knock onto the shaft with the hammer.
(Secure lock washer against falling with adhesive tape) (Fig. B1 - B4).
C. Mount foot left and right (4 a, b) on the base frame, each with 4 lenticular flange head screws M8x16 (8 a) and locking
nut M8 (8 b) (Fig. C1 - C4). Lightly tighten all frame screws by hand.
D. Screw rear strut (3) onto the mounted feet with 4 lenticular flange head screws M8x16 (8 a) and locking nut M8 (8 b).
Mount strut left and right (6 a, b) on the side of the feet (4 a, b), each with 5 lenticular flange head screws M8x16 (8 a)
and locking nut M8 (8 b). (Fig. D1, D2, D3).
E. Place machine on the feet, cut the cable tie, release the locking lever and tilt the swivel out.
all frame screws well. It is important here that the swivel log saw stands on a level surface. Mount swivel protection
(17) on the inside of the swivel with 2 mushroom head screws M6 x 12, 2 washers 6mm and 2 self-locking nuts M6
respectively and tighten securely. Make sure that the mushroom head screws are guided in from the outside. (Fig. E3).
F. Mount guard bracket (15) on the right rear foot with 2 lenticular flange head screws M8x16 (8 a) and locking nut M8
(8 b). (Fig. F)
30 GB
 www.scheppach.com /  service@scheppach.com /  +(49)-08223-4002-99 /  +(49)-08223-4002-58
(Fig. 8a)
(Fig. 8b)
(Fig. 9a)
(Fig. 9b)
(Fig. 10)
(Fig. 11)
(Fig. 12a)
(Fig. 12b)
(Fig. 13a)
(Fig. 13b)
(Fig. 13c)
(Fig. 13d)
(Fig. 13e)
(Fig. 13g)
(Fig. 13h)
(Fig. 17a)
(Fig. 17b)
(Fig. 17c)
(Fig. 18a)
(Fig. 18b)
(Fig. 18c)
(Fig. 18d)
(Fig. 18e)
(Fig. 18f)
(Fig. 18g)
(Fig. 18h)
(Fig. 18j)
(Fig. 18k)
(Fig. 18m)
(Fig. E1, E2). Tighten