Télécharger Imprimer la page

Prowork PBS 1835 Mode D'emploi page 22

Publicité

Les langues disponibles
  • FR

Les langues disponibles

  • FRANÇAIS, page 26
Anleitung PBS 1835 SPK1
GB
B
C
A
18
FUEL FILTER
CAUTION: Never use the saw without a fuel
filter. After 20 hours in operation the fuel fil-
ter should be cleaned or, in case of dam-
age, replaced. Be sure to empty the fuel
tank before changing the filter.
1.
Remove the fuel tank cap.
2.
Bend a piece of soft wire.
3.
Reach into fuel tank opening and hook fuel line.
Carefully pull the fuel line toward the opening until
you can reach it with your fingers.
NOTE: Do not pull hose completely out of tank.
4.
Lift filter (A) out of tank (Fig. 19).
5.
Pull off the filter with a twist and clean it; if the filter
is damaged, dispose of it.
6.
Insert a new filter. Place one end of the filter into the
tank opening. Make sure that the filter is seated in
the lower corner of the tank. If necessary, use a
long screwdriver to move the filter to its correct posi-
tion, taking care not to damage in the process.
7.
Fill tank with fresh fuel / oil mixture. See Section
FUEL AND LUBRICATION. Install fuel cap.
A
19
SPARK ARRESTER SCREEN (Fig. 20A)
NOTE: A clogged spark arrester screen will dramatically
reduce engine performance.
1.
Remove the 2 bar retaining nuts (A) and loosen the
2 screws (B) that secure the chain brake cover
(Fig. 20A).
2.
Remove the chain brake cover. Remove the 3
screws that hold the muffler to the cylinder. The
muffler will lift off after retaining screws are removed
(Figure 20B).
3.
Separate muffler halves (C). Remove the metal
baffles (D) and spacer tubes (E).
4.
Discard the used spark arrester screen and replace
it with a new one (F) (Fig. 20B).
5.
Reassemble the muffler components and install the
muffler to the cylinder. Tighten screws securely.
22
28.04.2006
9:03 Uhr
Seite 22
A
B
C
20A
SPARK PLUG
NOTE: For efficient operation of saw engine, spark plug
must be kept clean and properly gapped.
1.
Push STOP switch down.
2.
Remove the cover by undoing the cover fastening
screws (Fig. 21).
3.
Disconnect the ignition cable (A) from the spark plug
by pulling and twisting it simultaneously (Fig. 21).
4.
Reinstall a new spark plug, gapped at 0.6mm.
B
21
CARBURETOR ADJUSTMENT
The carburetor was pre-set at the factory for optimum
performance. If further adjustments are necessary,
please take your unit to the nearest professional.
STORING A CHAIN SAW
CAUTION: Never put a chain saw into stor-
age for longer than 30 days without carrying
out the following steps.
Storing a chain saw for longer than 30 days requires
storage maintenance. Unless the storage instructions are
followed, fuel remaining in the carburetor will evaporate,
leaving gum-like deposits. This could lead to difficult
starting and result in costly repairs.
1.
Remove the fuel tank cap slowly to release any
pressure in tank. Carefully drain the fuel tank.
2.
Start the engine and let it run until the unit stops to
remove fuel from carburetor.
3.
Allow the engine to cool (approx. 5 minutes).
4.
Using a spark plug wrench, remove the spark plug.
5.
Pour 1 teaspoon of clean 2-cycle oil into the
combustion chamber. Pull starter rope slowly
several times to coat internal components. Replace
spark plug (Fig. 22).
NOTE: Store the unit in a dry place and away from
possible sources of ignition such as a furnace, gas hot
water heater, gas dryer, etc.
E
F
D
20B
A
22

Publicité

loading

Ce manuel est également adapté pour:

45.014.89