Maytag RS-1 Mode D'emploi page 17

Oven Light
CAUTIONS:
•
Disconnect power to range before
replacing light bulb.
•
Use a dry potholder to prevent pos-
sible harm to hands when replacing
bulb.
•
Be sure bulb is cool before touching.
•
Do not touch hot bulb with a damp
cloth as this may cause the bulb to
break.
To replace:
1. When oven is cool, hold bulb cover in
place, then slide wire retainer off cover.
NOTE: Bulb cover will fall if not held
in place while removing wire retainer.
2. Remove bulb cover and light bulb.
3. Replace with a 40 watt appliance bulb.
4. Replace bulb cover and secure with
wire retainer.
5. Reconnect power to range. Reset clock.
BULB COVER
WIRE
RETAINER
Storage Drawer
The storage drawer at the bottom of the
range is safe and convenient for storing
metal and glass cookware. DO NOT store
plastic, paperware, food or flammable ma-
terial in this drawer. Remove drawer to
clean under range.
To remove:
Empty drawer then pull
out to the first stop position. Lift up front of
drawer and pull to the second stop posi-
tion. Grasp sides and lift up and out to
remove drawer.
To replace:
Fit the ends of the drawer
glides onto the rails. Lift up drawer front
and gently push in to first stop position.
Lift up and continue to slide drawer to the
closed position.
Electrical
Connection
Appliances which require
electrical power are
equipped with a three-
prong grounding plug
which must be plugged
directly into a properly
grounded three-hole 120 volt electrical out-
let.
Always disconnect power to appliance
before servicing.
The three-prong grounding plug offers
protection against shock hazards. DO
NOT CUT OR REMOVE THE THIRD
GROUNDING PRONG FROM THE
POWER CORD PLUG.
If an ungrounded, two-hole or other type
electrical outlet is encountered, it is the
personal responsibility of the appliance
owner to have the outlet replaced with a
properly grounded three-hole electrical
outlet.
Leveling Legs
CAUTION:
• Be sure the anti-tip bracket secures
one of the rear leveling legs to the
floor to prevent the range from
accidentally tipping.
The range should be leveled
when installed. If the range is
not level, turn the plastic level-
ing legs, located at each cor-
ner of the range, until
range is level.
LEVELING LEG
Removal of Gas
Appliance
Gas appliance connectors used to con-
nect this appliance to the gas supply are
not designed for continuous movement.
Once installed, DO NOT repeatedly move
this gas appliance for cleaning or to relo-
cate. If this appliance has to be moved
and/or removed for servicing, follow the
procedure described in the installation
instructions. For information, contact
Maytag Customer Service at 1-800-688-
9900.
To prevent range from accidentally tip-
ping, range must be secured to the floor
by sliding rear leveling leg into the anti-
tip bracket.
Oven Bottom
Protect oven bottom against
spillovers, espe-
cially acidic or
sugary spills, as
they may discolor
the porcelain
enamel. Use the
correct pan size to
avoid spillovers and boilovers.
The oven bottom may be removed for
easier cleaning.
To remove:
oven racks. Slide the two catches, located
at each rear corner of the oven bottom,
toward the front of the oven.
Lift the rear edge of the oven bottom
slightly, then slide it back until the front
edge of the oven bottom clears the oven
front frame. Remove oven bottom from
oven.
To replace:
oven bottom into the oven front frame.
Lower the rear of the oven bottom and
slide the two catches back to lock the oven
bottom in place.
ANTI-TIP BRACKET
1
2
3
When cool, remove the
Fit the front edge of the
16