Chicco Sprint Mode D'emploi page 17

CLEANING AND MAINTENANCE
The cleaning and maintenance of this product must be carried out on a regular
basis by the user. The cleaning and maintenance of the stroller must only be
carried out by an adult.
CLEANING
The cover can be removed (please refer to the section "How to Remove the
Fabric Cover").
Please refer to the care labels for instructions on how to clean the fabric parts.
Below are the cleaning symbols and their meanings:
Wash by hand in cold water
Do not bleach
Do not tumble dry
Do not iron
Do not dry clean
Periodically wipe clean plastic parts with a soft damp cloth. Always dry the
metal parts to prevent the formation of rust if the stroller has come into
contact with water.
MAINTENANCE
Lubricate the moving parts only if necessary, with a light application of a
silicone based lubricant. Regularly check the condition of the wheels and, keep
them clean of dust and sand. To avoid friction that may prevent the correct
operation of the stroller, ensure that all the movable plastic parts placed along
the metal frame are clean of dust, dirt or sand. Keep the stroller in a dry place.
GENERAL INSTRUCTIONS
WHEELS ASSEMBLY
In some configurations, the wheels may come not assembled. In this case,
assemble them as indicated below.
1. Insert the rear wheel blocks as indicated in figure 1, until they lock in position.
2 .Then insert the front wheel block on the stroller until it locks in position (fig.
2). Repeat this operation for the other wheel block.
WARNING: before use, make sure that the wheel blocks are secured correctly,
pulling them firmly.
HOW TO OPEN THE STROLLER
WARNING: When opening the stroller, ensure that your child, or other children,
are at a safe distance. Ensure that during these operations the movable parts
of the stroller do not come into contact with your child.
3. Pull the trigger opening mechanisms, located on the handles of the stroller, at the
same time; the stroller will start to open (diag. 3).
4. Lift the stroller towards you to make the opening operation easier (diag. 4).
5. Press the rear locking mechanism in a downward direction with the tip of
your foot to open the stroller fully, and lock it in the open position (diag. 5).
WARNING: Ensure that the stroller is locked in the open position, by checking
that the rear locking mechanism is effectively secured.
BACKREST ASSEMBLY
COMPONENTS
A) Backrest tube
B) Connection of backrest tube
C) Front release button
D) Rear joint
E) Rear release button
6. To assemble the backrest, insert both backrest tubes (A) in the corresponding
coupling (B) as shown in fig. 6.
7. Once the two tubes are inserted in the coupling, rotate the rear joint (D) so
as to align rib F with housing G (fig. 7A) and insert the pin present on the frame,
inside the hole of the rear joint until you hear a click (fig. 7B).
WARNING: before using the product in the stroller configuration, always check
the correct assembly of the backrest.
BACKREST FITTING
8. Fit the cover on the stroller's backrest from the top (fig. 8A-8B).
9. Thread the safety harness abdominal straps through the slots located on the
side of the backrest cover (fig. 9).
10. Thread the crotch strap leg divider through the slot located on the backrest
cover (fig. 10).
11. Insert the adjustable leg rest in the relative fabric pocket located under
the backrest cover (fig. 11).
12. Fasten the cover to the seat, securing the two press buttons present on the
bottom of the seat (fig. 12).
13. Fasten the armrest covers, by securing the 2 press buttons (fig. 13).
14. Fasten the side edge of the backrest cover with Velcro to the armrest cover,
as indicated in fig. 14.
CARRY-ALL BASKET
The stroller features a large carry-all basket.
15. To secure the basket to the stroller, as shown in fig. 15, secure first of all the
2 plastic hooks (H) to the pins on the front of the structure. Next, insert the 2
strings on the basket, in the two plastic slots under the seat and secure them
by means of the press buttons (I). Finally, secure the remaining 4 strings with
the press buttons, to the rear tubes of the stroller (K).
WARNING: do not store weights exceeding 5 kg in the basket. Remove the
content inside the basket before folding the stroller.
CANOPY
The stroller features two fixings on the sides to secure the canopy.
16. To fasten the canopy to the structure, insert the canopy joint in the relative
fixing on the stroller's structure (fig. 16).
17. To open the canopy, push the front brace forward (fig. 17).
18. To remove the canopy, pull the canopy joint upwards (fig. 18).
WARNING: the canopy fastening operation must be carried out on both sides
of the stroller. Check the proper locking of them on both sides.
REMOVABLE BUMPER BAR
19. To remove the bumper bar, press the two buttons located under the armrests
(diag. 19) and pull the bumper bar towards you.
Open only one side of the bumper bar to place the child into the stroller more easily.
WARNING: Always fasten the child with the safety harness. The bumper bar
is NOT a child restraint device.
WARNING: Never use the bumper bar to lift the stroller with the child sitting in it.
WARNING: In order to fix the car seat or the bag to the stroller, the bumper
bar must be removed.
HOW TO USE THE SAFETY HARNESS
This stroller has a 5-point safety harness that features two shoulder straps, a
waist strap and a crotch strap with buckle.
WARNING: When using the safety harness with children from birth up to
approximately 6 months of age, it is necessary to first fit the shoulder straps
through the two adjustment holes on the fabric backrest (diag. 20A).
20. Check that the shoulder straps are adjusted at the correct height for your
child. If they are not at the correct height, adjust them as required (diag. 20 B).
21. After sitting the child in the stroller, insert the 2 prongs into the buckle and,
if necessary, adjust the width of the waist belt operating the buckles (diag. 21).
22. To unfasten the waist strap, press and pull the side prongs at the same
time (diag. 22).
WARNING: To ensure your child's safety, it is necessary to always use the
safety harness.
WARNING: the use of the crotch strap and safety harness is necessary to
guarantee the safety of your child.
WARNING: After removal of the safety harness (e.g. for washing), ensure that
the harness is reassembled correctly using the anchorage points. The harness
must be re adjusted. To ensure that the harness is adjusted correctly, fitting
your child and securely closed, pull firmly on the end of the harness (on the
underside of the seat).
HOW TO ADJUST THE BACKREST
23. To adjust the inclination of the backrest, press the button located on the
backrest. Release the button to lock the backrest in the nearest position. To
raise the backrest, simply push it in an upward direction (diag. 23).
WARNING: The child's weight can make these operations more difficult.
ADJUSTING THE LEG REST
24. Press the two edges of the leg rest to adjust it to the desired position (fig. 24).
DOUBLE-TWIST ADJUSTABLE ERGONOMIC HANDGRIP
25. By pressing the button on the handle, it is possible to rotate the handgrip to
the desired position, adapting it to the height and most comfortable position
for the user (fig. 25). The handgrip can be adjusted in 8 different positions.
26. WARNING: during use, the handgrip must not be used in lowered position
(fig. 26A). During use, the handgrips must be adjusted at the high position,
as shown in figure 26B.
17