Electronic Controls Set-Up Instructions - Whirlpool W11449282C Instructions D'installation

Basic Operation of Commercial Washer
For additional information, see
■
www.WhirlpoolCommercialLaundry.com.
WARNING
Electrical Shock Hazard
Disconnect power before servicing.
Replace all parts and panels before operating.
Failure to do so can result in death or electrical shock.
IMPORTANT
Electrostatic Discharge (ESD)
Sensitive Electronics
ESD problems are present everywhere. ESD may damage
or weaken the electronic control assembly. The new control
assembly may appear to work well after repair is finished, but
failure may occur at a later date due to ESD stress.
Use an anti-static wrist strap. Connect wrist strap to green
■
ground connection point or unpainted metal in the washer.
Touch your finger repeatedly to a green ground connection
point or unpainted metal in the washer.
Before removing the part from its package, touch the
■
anti-static bag to a green ground connection point or
unpainted metal in the washer.
Avoid touching electronic parts or terminal contacts; handle
■
electronic control assembly by edges only.
When repackaging failed electronic control assembly in
■
anti-static bag, observe above instructions.
GENERAL INFORMATION
Blank Display
Check power to machine. Enter Service Mode and check for
Fault Code.
'0 Minutes' showing in display
This indicates the previous cycle is complete or a machine reset
was performed. Opening the lid will restore the display to the
Vend Price or Available state.
Factory Default Settings
Washer is programmed at the factory as follows:
HEAVY DUTY = Hot Water Main Wash - Deep Rinse - Heavy
■
Soil Option Enabled- Extra Rinse Option Enabled - COIN
model pricing set to $2.50.
MIXED = Warm Water Main Wash - Deep Rinse - No Options
■
Enabled - COIN model pricing set to $2.00.
DELICATES = Cold Water Main Wash - Deep Rinse - No
■
Options Enabled - COIN model pricing set to $1.75.
NORMAL ECO = Warm Water Main Wash - Progressive Spray
■
Rinse - No Options Enabled - COIN model pricing set to
$1.75.
Refer to Cycle Settings in Program Menu to change default
settings.

ELECTRONIC CONTROLS SET-UP INSTRUCTIONS

-OR-
Warm Start (after power failure)
After a delay of up to 8 seconds, the washer is restored to
the portion of the cycle that existed at time of the power failure.
To continue the cycle, press START.
Free Cycles
This is established by setting the cycle price to zero. When this
happens, 'SELECT CYCLE' will appear and cycle price will show
0.00.
Debit Card Ready
This washer is debit card 'cable' ready. It will accept a variety of
debit card systems, but does NOT come with a debit card reader.
Refer to the debit card reader manufacturer for proper washer
setup. In models converted to a Generation 1 debit card system,
debit pulses represent the equivalent of one coin (coin 1).
Display
After the washer has been installed and plugged in, the display
will show 'SYnC' for a few seconds, then '0 MINUTES'. Once the
washer has been plugged in and the washer door opened and
closed, the display will show the price. In washers set for free
cycles, the display will flash 'SELECT CYCLE', and will display
'PRICE 0.00'.
CYCLES
HEAVY DUTY
NORMAL
DELICATES
NORMAL
ECO
Control Set-Up Procedures
IMPORTANT: Read all instructions before operating.
The lower fabric setting keypads and the digital display are
used to set up the controls. The display can contain four
numbers and/or letters and a decimal point. These are used to
indicate the set-up codes and related code values available for
use in programming the washer.
How to use the keypads to program the controls
1. The HEAVY DUTY keypad is used to adjust the values
associated with set-up codes. Pressing the keypad will
increment the value.
Rapid adjustment is possible by holding the keypad down.
2. The MIXED keypad will advance you through the set-up codes.
Pressing the keypad will advance you to the next available
set-up code. Holding the keypad down will automatically
advance through the set-up codes at
a rate of one (1) per second.
3. The DELICATES keypad is used to select or deselect options.
4. The TEMPERATURE keypad is used to decrease set-up code
value.
Start Operating Set-Up
COIN Models: Insert access door key, turn, and lift to remove
■
access door.
NON-COIN models set for free vend: Refer to bottom of page
■
11 for entering operating setup.
NON-COIN Models: Once the debit card reader is installed
■
(according to the reader manufacturer's instructions), the set-
up mode can be entered by inserting a set-up card (supplied
by the reader manufacturer) into the card slot. If a manual set-
up card is not available, manual set-up mode can be entered
by removing connector J4 on the circuit board.
IMPORTANT: The console must not be opened unless power is
first removed from the washer. To access connector J4:
g
Unplug washer or disconnect power.
OPTIONS
TEMPERATURE
SOIL LEVEL
EXTRA RINSE
11